Subscribe to Our Youtube Channel
Related Manuals for Compatible Systems Octal V.35 - 10/100 RIOP
Summary of Contents for Compatible Systems Octal V.35 - 10/100 RIOP
- Page 1 Octal V.35 - 10/100 RIOP Installation Guide Compatible Systems Corporation 4730 Walnut Street Suite 102 Boulder, Colorado 80301 303-444-9532 800-356-0283 http://www.compatible.com...
- Page 2 Octal V.35-10/100 RIOP Installation Guide, Version 1.0 Copyright© 1999, Compatible Systems Corporation All rights reserved. VSR, VSR-2, MicroRouter and CompatiView are trademarks of Compatible Systems Corporation. Other trademarks are the property of their respective holders. FCC Notice: This product has been certified to comply with the limits for a Class A computing device, pursuant to Subpart J of Part 15 of FCC Rules.
-
Page 3: Table Of Contents
Table of Contents Introduction to the Octal V.35-10/100 RIOP Chapter 1 - Network Installation Connecting the Octal V.35-10/100 to the Ethernet Telco Line Connection Requirements Connecting a Line Device to the V.35 Interfaces Connecting a Management Console Powering Up the Router Chapter 2 - Quickstart Instructions THERNET NTERFACE... - Page 4 Table of Contents Required for IP Unnumbered Interface Suggested for IP IPX Protocol Required for IPX Suggested for IPX AppleTalk Protocol Required for AppleTalk Suggested for AppleTalk DECnet Protocol Required for DECnet SMDS Configuration Link Configuration SMDS Addressing AVING A ONFIGURATION ILE TO LASH...
-
Page 5: Introduction To The Octal V.35-10/100 Riop
Introduction to the Octal V.35-10/100 RIOP Introduction to the Octal V.35-10/100 RIOP The Octal V.35-10/100 Routing Input/Output Processor (RIOP), as part of the VSR multigi- gabit switching router, allows you to connect a local Ethernet and up to eight remote corporate networks. -
Page 6: Chapter 1 - Network Installation
Note: Ethernet cables and cable connectors are not supplied with the Octal V.35-10/100 RIOP product. Category 5 cabling is required for 100 BaseT operation. Please contact your reseller or your Compatible Systems representative for information on obtaining the correct Ethernet cabling supplies. -
Page 7: Telco Line Connection Requirements
1 stop bit and no Flow Control. v Note: The Octal V.35-10/100 RIOP also has an AUX interface. This is a modem connection which should only be used in consultation with Compatible Systems Technical Support staff, who will provide instruction on its use. -
Page 8: Chapter 2 - Quickstart Instructions
Chapter 2 - Quickstart Instructions Chapter 2 - Quickstart Instructions This Quickstart chapter briefly discusses the major parameters that must be set in order to use the Octal V.35-10/100 RIOP as part of your VSR multigigabit switching router. Detailed information on the meaning of the router’s parameters is provided in the Compa- tiView Management Software Reference Guide and the Text-Based Configuration and Command Line Management Reference Guide. -
Page 9: Suggested For Ip
Chapter 2 - Quickstart Instructions Suggested for IP These parameters help supply information about the segment that the interface is connected to. With this information, routing can take place. • Set IP RIP 1, IP RIP 2 or OSPF (Open Shortest Path First) •... -
Page 10: Suggested For Decnet
Chapter 2 - Quickstart Instructions In CompatiView you must set a global parameter and a port-specific parameter. Suggested for DECnet Setting the parameters above should be adequate for most installations. WAN Interface Configuration The default setting for all WAN interfaces on your Octal V.35-10/100 RIOP is Off for all protocols and for the link configuration. -
Page 11: Ipx Protocol
Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration parameters, and other configuration questions, refer to the Tech Support pages on the Compatible Systems Web site at: http://www.compatible.com/. -
Page 12: Wan Link Configuration
Dedicated line operation generally does not require additional parameters for operation. Frame Relay DLCI Mappings If you are connecting to another Compatible Systems router, this information is not required for Frame Relay operation. Compatible Systems uses IARP (Inverse Address Resolution Protocol) to dynamically generate this information. -
Page 13: Suggested For Ip
Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration parameters, and other configuration questions, refer to the Tech Support pages on the Compatible Systems Web site at: http://www.compatible.com/. -
Page 14: Decnet Protocol
Chapter 2 - Quickstart Instructions TB: Use configure and set keywords in the AppleTalk WAN 0 (and/or any other port you wish to configure) section. DECnet Protocol Required for DECnet In order to be used, DECnet must be turned on both globally and for a particular port. WAN interfaces which are set for Frame Relay operation do not need any additional parame- ters set in order to function. -
Page 15: Chapter 3 - Shipping Defaults
Chapter 3 - Shipping Defaults Chapter 3 - Shipping Defaults Ethernet Interface IP Routing Defaults • • Address: 198.41.12.1 • Subnet Mask: 255.255.255.0 • Broadcast Address: 198.41.12.255 • IP RIP off IPX Routing Defaults • 802.3 on, autoseeding • 802.2 on, autoseeding •... -
Page 16: Chapter 4 - Led Patterns
In addition to indicating certain router-wide operating conditions, they may also display port- specific information. v Note : Any continuous flashing pattern not noted in this chapter may be caused by a hard- ware failure. Please call Compatible Systems Technical Support if your router shows a hard- ware failure. Router LED Patterns The following LEDs and light patterns provide information about the VSR’s physical state and... -
Page 17: Appendix A - Connector And Cable Pin Outs
Appendix A - Connector and Cable Pin Outs Appendix A - Connector and Cable Pin Outs Pin Outs for HD D-Sub Male to V.35 Male Cable V.35 DTE – DCE Signal Chassis Ground Signal Ground Request to Send Clear to Send Data Set Ready Receive Line Signal Detect Data Terminal Ready...
Need help?
Do you have a question about the Octal V.35 - 10/100 RIOP and is the answer not in the manual?
Questions and answers