Related Manuals for Compatible Systems Octal T1-10/100 RIOP
Summary of Contents for Compatible Systems Octal T1-10/100 RIOP
-
Page 1: Installation Guide
Octal T1-10/100 RIOP Installation Guide Compatible Systems Corporation 4730 Walnut Street Suite 102 Boulder, Colorado 80301 303-444-9532 800-356-0283 http://www.compatible.com... - Page 2 Octal T1-10/100 RIOP Installation Guide, Version 1.0 Copyright© 1999, Compatible Systems Corporation All rights reserved. VSR, VSR-2, MicroRouter and CompatiView are trademarks of Compatible Systems Corporation. Other trademarks are the property of their respective holders. FCC Notice: This product has been certified to comply with the limits for a Class A computing device, pursuant to Subpart J of Part 15 of FCC Rules.
-
Page 3: Table Of Contents
Table of Contents Introduction to the Octal T1-10/100 RIOP Chapter 1 - Network Installation Connecting the Octal T1-10/100 to the Ethernet Connecting the Octal T1-10/100 to a T1 Line Connecting a Management Console Powering Up the Router Chapter 2 - Quickstart Instructions... - Page 4 Table of Contents IP Protocol Required for IP Numbered Interface Required for IP Unnumbered Interface Suggested for IP IPX Protocol Required for IPX Suggested for IPX AppleTalk Protocol Required for AppleTalk Suggested for AppleTalk DECnet Protocol Required for DECnet SMDS Configuration WAN Link Configuration SMDS Addressing AVING A...
-
Page 5: Introduction To The Octal T1-10/100 Riop
Each of the T1 interfaces has a data capacity of 1.544 Mbps, while the Ethernet interface can operate at either 10 Mbps or 100 Mbps. This section of the manual contains information specific to the Octal T1-10/100 RIOP. It is divided into the following sections:... -
Page 6: Chapter 1 - Network Installation
Chapter 1 - Network Installation Octal T1-10/100 RIOP Front Panel This section of the manual will help you install the Octal T1-10/100 RIOP to connect a local Ethernet and up to eight remote corporate networks. These connections can be made to other Compatible Systems devices or internetworking equipment from other vendors. -
Page 7: Connecting A Management Console
The default settings for the Console interface are VT100 terminal emulation, 9600 bps, 8 bits, no parity, 1 stop bit and no Flow Control. v Note: The Octal T1-10/100 RIOP also has an AUX interface. This is a modem connection which should only be used in consultation with Compatible Systems Technical Support staff, who will provide instruction on its use. -
Page 8: Chapter 2 - Quickstart Instructions
This Quickstart chapter briefly discusses the major parameters that must be set in order to use the Octal T1-10/100 RIOP as part of your VSR multigigabit switching router. Detailed information on the meaning of the router’s parameters is provided in the Compa- tiView Management Software Reference Guide and the Text-Based Configuration and Command Line Management Reference Guide. -
Page 9: Ipx Protocol
Chapter 2 - Quickstart Instructions • IP static routes CV: Use the TCP/IP Routing: Ethernet 0 Dialog Box to set RIP, and the IP Static Routing Dialog Box (under Global/IP Static Routes) to set static routes. OSPF can only be configured using text-based configuration. -
Page 10: Wan Interface Configuration
Chapter 2 - Quickstart Instructions WAN Interface Configuration The default setting for all WAN interfaces on your Octal T1-10/100 RIOP is Off for all proto- cols and for the link configuration. In order to use a WAN interface, you may first need to set some physical parameters and then set up the link and protocol parameters. -
Page 11: Ipx Protocol
Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration parameters, and other configuration questions, refer to the Tech Support pages on the Compatible Systems Web site at: http://www.compatible.com/. -
Page 12: Suggested For Dedicated Line Operation
Dedicated line operation generally does not require additional parameters for operation. Frame Relay DLCI Mappings If you are connecting to another Compatible Systems router, this information is not required for Frame Relay operation. Compatible Systems uses IARP (Inverse Address Resolution Protocol) to dynamically generate this information. -
Page 13: Ipx Protocol
Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration parameters, and other configuration questions, refer to the Tech Support pages on the Compatible Systems Web site at: http://www.compatible.com/. -
Page 14: Smds Configuration
Frame Relay operation. The only parameters which should be set differently for SMDS are the Link Configuration and the SMDS addressing section. WAN Link Configuration SMDS is presently supported in the Octal T1-10/100 RIOP only via synchronous dedicated line operation. •... -
Page 15: Chapter 3 - Shipping Defaults
Chapter 3 - Shipping Defaults Chapter 3 - Shipping Defaults Ethernet Interface IP Routing Defaults • • Address: 198.41.12.1 • Subnet Mask: 255.255.255.0 • Broadcast Address: 198.41.12.255 • IP RIP off IPX Routing Defaults • 802.3 on, autoseeding • 802.2 on, autoseeding •... -
Page 16: Ipx Defaults
Chapter 3 - Shipping Defaults IPX Defaults • • Unnumbered interface AppleTalk Defaults • • Unnumbered interface DECnet Defaults • T1 CSU/DSU Defaults • Full T1 • Slave clock • B8ZS encoding • ESF framing •PRM transmit • Accept V.54 or line loopback commands from remote WAN 1 - 7 Interfaces IP Defaults •... -
Page 17: Chapter 4 - Led Patterns
In addition to indicating certain router-wide operating conditions, they may also display port- specific information. v Note : Any continuous flashing pattern not noted in this chapter may be caused by a hard- ware failure. Please call Compatible Systems Technical Support if your router shows a hard- ware failure. Router LED Patterns The following LEDs and light patterns provide information about the VSR’s physical state and... -
Page 18: Octal T1-10/100 Riop Led Patterns
Chapter 4 - LED Patterns Octal T1-10/100 RIOP LED Patterns The following LEDs and light patterns provide information about the Octal T1-10/100 RIOP interfaces. Ethernet Traffic Indicators Scan from 1 to 3: Ethernet transmit packet Scan from 5 to 3: Ethernet receive packet...
Need help?
Do you have a question about the Octal T1-10/100 RIOP and is the answer not in the manual?
Questions and answers