2006 SuperJet OWNER’S/OPERATOR’S MANUAL U.S.A. Edition READ THIS MANUAL CAREFULLY BEFORE OPERATION! LIT-18626-06-50...
EJU00989 To the owner/operator Thank you for choosing a Yamaha water- EJU01265 Important manual information: craft. This Owner’s/Operator’s Manual con- In this manual, information of particular tains information you will need for proper importance is distinguished in the following operation, maintenance, and care.
EJU00992 CONTENTS GENERAL AND SAFETY INFORMATION FEATURES AND FUNCTIONS OPERATION MAINTENANCE AND CARE TROUBLESHOOTING AND EMERGENCY PROCEDURES APPENDIX READ THIS OWNER’S/OPERATOR’S MANUAL CAREFULLY BEFORE OPERATING YOUR WATERCRAFT.
EJU00993 GENERAL AND SAFETY INFORMATION Identification numbers ......1-1 Primary Identification (PRI-ID) number ...........1-1 Hull Identification Number (HIN) ....1-1 Engine serial number ......1-1 Emission control information ....1-2 Approval label of Emission control certificate ..........1-2 Manufactured date label ......1-2 Important labels ........1-3 Label location .........1-3 Warning labels ........1-4 Other labels ..........1-6...
Hull Identification Number (HIN) and engine serial number in the spaces pro- vided for assistance when ordering spare parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case your watercraft is stolen.
EJU01846 Emission control information This engine conforms to 2006 U.S. Envi- ronmental Protection Agency (EPA) regula- tions for marine SI engines. EJU01126 Approval label of Emission control certificate This label is attached to the electrical box and muffler. 1 Emission control information label EJU01127 Manufactured date label This label is attached to the electrical box...
Limitations on who may Safety information operate the watercraft The safe use and operation of this Yamaha recommends a minimum opera- watercraft is dependent upon the use of tor age of 16 years old. proper riding techniques, as well as upon Adults must supervise use by minors.
This is a high performance boat—not a EJU12691 Cruising limitations toy. Sharp turns or jumping wakes or waves can increase the risk of back/spinal injury (paralysis), facial injuries, and bro- ken legs, ankles and other bones. Do not jump wakes or waves. Do not operate the watercraft in rough water, bad weather or when visibility is poor;...
EJU11441 Operation requirements All riders must wear a U.S. Coast Guard (USCG) approved personal flotation device (PFD) that is suitable for personal watercraft use. Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into water or being near the jet thrust nozzle.
Helmets meeting Snell or DOT standards are required for IJSBA-sanctioned races. You must decide whether to wear a hel- met while you ride for recreation. You should know that a helmet could help pro- tect you in certain kinds of accidents and that it could injure you in others.
A mir- ror can also be used as an emergency signal. Contact your Yamaha dealer or the Coast Guard for more information. Watch Scan carefully for swimmers, and stay A watch is helpful so you will know how away from swimming areas.
EJU01003 EJU01271 Hazard information Watercraft characteristics Jet thrust turns the watercraft. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. You may still have some turning ability immediately after releasing the throttle, but once the engine slows down, the watercraft will no longer respond to...
Keep away from intake grate 1 while the engine is on. Items such as long hair, loose clothing, or PFD straps can become entangled in moving parts resulting in severe injury or drowning. Never insert any object in the jet thrust nozzle 2.
Rules of the Road Whenever two vessels on the water meet one another, one vessel has the right-of- Yamaha watercraft is legally consid- way; it is called the “stand-on” vessel. The ered a powerboat. Operation of the vessel that does not have the right-of-way is watercraft must be in accordance with called the “give-way”...
Rules when encountering Meeting If you are meeting another power vessel vessels head on, and are close enough to run the There are three main situations that you risk of collision, neither of you has the right- may encounter with other vessels which of-way! Both of you should alter course to could lead to a collision unless the Steering avoid an accident.
Overtaking Sailing vessel right-of-way If you are passing another vessel, you are Sailing vessels should normally be given the give-way vessel. This means that the the right-of-way. The exceptions to this are: other vessel is expected to maintain its 1. When the sailing vessel is overtaking the course and speed.
This system uses buoys and signs with Remember, markings may vary by geo- distinctive shapes and colors to show regu- graphic location. Always consult local boat- latory or advisory information. These mark- ing authorities before riding your watercraft ers are white with black letters and orange in unfamiliar waters.
Yamaha is the watercraft industry’s lead- EJU01181 To get more boating ing manufacturer to build awareness and support for boating education. In 1997, safety information Yamaha launched its GET W.E.T. (Water- Be informed about boating safety. Addi- craft Education and Training) initiative and...
EJU01006 Enjoy your watercraft responsibly You share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courtesy. Whenever and wherever you ride, think of yourself as the guest of those around you.
EJU01007 FEATURES AND FUNCTIONS Location of main components ....2-1 Operation of controls and other functions ...........2-3 Hood ............2-3 Fuel tank filler cap ........2-4 Fuel cock knob ........2-4 Engine stop switch .........2-5 Engine shut-off switch ......2-5 Choke knob ..........2-6 Throttle lever ..........2-6 Start switch ..........2-6 Cooling water pilot outlet .......2-7 Steering system ........2-7...
EJU01008 Location of main components 1 Rope hole 9 Hood latch Use to attach rope for transporting, mooring or Locks the hood. 0 Jet thrust nozzle towing the watercraft in an emergency. 2 Storage pouch Changes the direction of jet thrust according 3 Steering pole to handlebar position.
1 Fire extinguisher container 8 Engine stop switch Use to store the fire extinguisher. Push to stop the engine normally. 2 Fuel cock knob 9 Engine shut-off cord (lanyard) Use to select either normal or reserve fuel flow Attach to wrist so that the engine stops if the from the fuel tank to the carburetors, or to shut operator falls off the watercraft.
EJU01009 Operation of controls and other functions EJU01272 Hood The hood is secured at the rear by a latch. Lift the steering pole and support it with the lock pin before removing the hood. To remove the hood: 1. Turn the latch knob 1 to the open posi- tion, and then pull up on the hood latch 2 to unlatch the hood.
2. Push down on the hood latch, and then turn the knob to the lock position. NOTE: Make sure that the hood is properly secured before operating the watercraft. EJU01012 Fuel tank filler cap To remove the fuel tank filler cap 1, turn it counterclockwise.
EJU01015 Engine stop switch Push this switch 1 (red button) to stop the engine normally. EJU01016 Engine shut-off switch Insert the clip 1, on the end of the engine shut-off cord 2, under the engine shut-off switch 3 (black button). The engine will stop automatically when the clip is removed from the switch, such as if the operator falls off the watercraft.
EJU01215 Choke knob Starting a cold engine requires a richer air-fuel mixture, which is supplied by the choke. Pull the knob 1 out to turn the choke on. Push the knob in to turn the choke off. EJU01018 Throttle lever Squeeze the throttle lever 1 to increase engine speed.
EJU11301 Cooling water pilot outlet This watercraft is equipped with a cooling water pilot outlet. When the engine is running, cooling water is circulated in the engine, and then it is discharged from the pilot outlet. To check for proper operation of the cool- ing system, check that water is being dis- charged from the pilot outlet.
EJU01273 Steering pole The steering pole varies in height with the operator’s posture, enabling the operator to assume various riding positions. When removing the hood for pre-opera- tion checks, maintenance, etc., lift the steer- ing pole 1 and use the lock pin 2 to support it.
EJU01274 Storage pouch A storage pouch is provided on the under- side of the hood for the Owner’s/Operator’s Manual, tool kit and other small items. Bend the Owner’s/Operator’s Manual slightly to insert it into the storage pouch 1, then add the tool kit and any other small items.
EJU01275 Fuel and oil EJU20550 Gasoline WARNING GASOLINE VAPORS HIGHLY FLAMMABLE AND EXPLOSIVE! Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. Stop engine before refueling. Refuel in a well-ventilated area with the watercraft in a horizontal position. Do not stand or sit on the watercraft while refueling in case of fire.
Gasohol containing ethanol can be used if ethanol content does not exceed 10% and the fuel meets minimum octane ratings. Gasohol containing methanol is not rec- ommended by Yamaha because it can cause fuel system damage or engine perfor- mance problems. EJU10441...
EJU01276 Mixing fuel and oil CAUTION: Avoid using any mixture of gasoline and oil other than those designated. Make sure gasoline and oil are thor- oughly mixed in the correct ratio, oth- erwise the following problems may occur. Too little oil in the fuel mixing ratio could result in major engine trou- ble, such as seizure.
EJU01277 Filling the fuel tank CAUTION: Be careful when refueling. Avoid getting water or other contaminants in the fuel tank. Contaminated fuel can cause poor running or engine damage. 1. Lift the steering pole and support it with the lock pin. 2.
EJU01346 Pre-operation checks EJU01347 Pre-operation check list Before operating this watercraft, perform the checks in the following check list. See the accompanying text in this chapter for details on how to perform the checks. WARNING If any item in the pre-operation check list is not working properly, have it inspected and repaired before operating the watercraft, otherwise an accident could occur.
Do not start the engine if there is a fuel leak or loose electrical connection. EJU20560 Hull Check the hull for cracks or other dam- age. If any damage is found, have a Yamaha dealer repair the watercraft.
EJU01279 Fuel system Check the fuel system for leakage, cracks or malfunctions before each use. (See page 4-10 for check points and correct pro- cedures.) 1. Remove the fuel tank filler cap to release any pressure that might have built up in the fuel tank.
EJU01280 Bilge Check for moisture and fuel residue in the bilge. Excessive water in the bilge can splash into the carburetor and engine which could cause engine damage. EJU01969 Battery Check the battery condition and the elec- trolyte level. Check that the battery leads are tightened securely and there is no corrosion on the battery terminals.
Always carry a fire extinguisher on board. A fire extinguisher is not standard equip- ment with this watercraft. If you do not have one, contact a Yamaha dealer or a fire extinguisher dealer to obtain one meeting the proper specifications.
EJU01834 Throttle Squeeze and release the throttle lever several times to make sure that there is no hesitation in its travel. It should be smooth over the complete range, and spring back to the idle position when released. WARNING Before starting the engine, always check the operation of the throttle lever.
EJU01058 Jet unit Carefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the intake is clogged, cavitation could occur, reducing jet thrust, and possibly damaging the jet pump. In some cases, the engine may overheat because of lack of cooling water, and dam- age to the engine could result.
EJU18352 Switches CAUTION: Do not run the engine of the watercraft for more than 15 seconds on land with- supplying water, otherwise engine may overheat. Check the start switch, the engine stop switch, and the engine shut-off switch for proper operation. Push the start switch 1 to start the engine.
Con- sult your Yamaha dealer about any con- trols or functions you do not fully understand. Failure to understand how controls work could cause an accident or prevent you from avoiding an accident.
3. Gradually open the throttle lever to 3/4 or less. 4. Continue operation at 3/4 throttle or less until the first tankful of fuel has been used. 5. Fill the tank once more with a fuel-to-oil ratio of 25:1, and proceed with normal operation.
EJU01137 Starting the engine WARNING Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monox- ide, a colorless, odorless gas that may cause loss of consciousness and death within a short time.
3. Attach the clip 1 to the engine shut-off switch 2. Also, attach the engine shut-off cord 3 to your left wrist. WARNING Check that the engine shut-off cord is not frayed or broken, and keep it free from the handlebars so the engine stops if the operator falls off.
6. Release the start switch as soon as the engine starts to run. CAUTION: Never push the start switch while the engine is running. Do not operate the start switch for more than 5 seconds, otherwise the battery will be discharged and the engine will not start.
EJU01066 Stopping the engine To stop the engine, release the throttle lever, and then push the engine stop switch (red button). WARNING You need throttle to steer. Shutting off the engine can cause you to hit an obsta- cle you are attempting to avoid. A colli- sion could result in severe injury or death.
EJU01068 EJU01147 Operating your watercraft Learning to operate your watercraft EJU01146 Getting to know your Before operating, always perform the pre-operation checks listed on page 3-5. watercraft The short time spent checking the watercraft Operating your watercraft requires skills will reward you with added safety and reli- acquired through practice over a period of ability.
Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into water or being near the jet thrust nozzle. Normal swimwear does not adequately protect against forceful water entry into rectum or vagina.
EJU01287 Starting the watercraft WARNING Scan constantly for people, objects and other watercraft. Be alert for con- ditions that limit your visibility or block your vision of others. Operate defensively at safe speeds and keep a safe distance away from people, objects and other watercraft.
EJU01378 Boarding and starting in deep water 1. Swim to the rear of the watercraft. Attach the engine shut-off cord to your wrist. Attach the clip to the engine shut-off switch. 2. Grasp the handlebars with both hands. Pull your body up onto the riding tray and balance there, using your elbows on the gunwales for leverage.
6. Move as far forward as possible without interfering with the movement of the han- dlebars. Keep your body perpendicular to the water, with your weight forward and low. 7. Once the bow drops, and the watercraft has leveled out in the water and reached planing speed, back off the throttle lever and select your desired speed.
EJU01289 Boarding and starting in shallow water Be sure to learn the deep-water starting method before operating the watercraft in water where it is too deep for you to stand. Do not try to start the watercraft in water less than 60 cm (2 ft) deep. 1.
EJU01290 Operating positions After you are underway, you may choose to kneel or stand, depending upon water- craft speed, your skill level, and your prefer- ence. Here are some guidelines. EJU01291 Kneeling It is easier to maintain your balance when kneeling than when standing.
EJU12931 Capsized watercraft If the watercraft capsizes, turn it over immediately. Be sure to carefully follow the procedures below to prevent injury or damage to the watercraft. WARNING IMPROPER UPRIGHTING CAN CAUSE INJURY: Shut the engine off by pulling on the engine shut-off cord to remove the clip from the engine shut-off switch.
3. Start the engine and operate the water- craft to discharge any water remaining in the engine compartment. (If the engine does not start, see page 5-6, “Towing the watercraft” or page 5-7, “Submerged watercraft.”) NOTE: To efficiently discharge water from the engine compartment, operate the water- craft as straight as possible and above planing speed for at least 2 minutes.
EJU01294 Turning the watercraft Steering control depends on the combi- nation of handlebar position and the amount of throttle. Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust nozzle, it creates thrust to move and steer the watercraft.
To maintain your balance, lean into a turn. How much you lean depends on the tight- ness of the turn and your traveling speed. In general, the higher the speed or the sharper the turn, the more you lean. WARNING Do not release the throttle when trying to steer away from objects—you need throt- tle to steer.
EJU01080 Stopping the watercraft The watercraft is not equipped with a sep- arate braking system. It is stopped by water resistance when throttle lever released. From full speed, the watercraft comes to a complete stop in approximately 90 m (300 ft) after the throttle is released and the engine is stopped, although this dis- tance will vary depending on many factors, including gross weight, water surface condi-...
EJU01081 Beaching the watercraft 1. Make sure no obstructions, boats or swimmers are near the beach. Release the throttle lever about 90 m (300 ft) before you reach the intended beaching area. 2. Approach the beach slowly and stop the engine before reaching land.
EJU01894 Post-operation checks Always perform the following post-opera- tion checks after operating the watercraft. 1. Remove the watercraft from the water. 2. Wash down the hull, steering pole, han- dlebars, and jet unit with fresh water. 3. Remove the hood and check the engine compartment for water.
CAUTION: Do not run the engine at full throttle or for more than 15 seconds on land, other- wise the engine may overheat and seize. 7. If the watercraft will be stored for a week or more, lubricate internal engine com- ponents to help prevent corrosion.
EJU01956 Transporting WARNING Always place the fuel cock knob in the “OFF” position when transporting the watercraft, otherwise fuel could leak out into the engine or engine compartment, which would create a fire hazard. Transport this watercraft using the special trailer that incorporates a hole into which the pin 1 can be inserted and locked after passing it through the rope hole 2.
EJU01086 MAINTENANCE AND CARE Storage ............4-1 Flushing the cooling system ....4-1 Lubrication ..........4-3 Fuel system ..........4-4 Battery ............4-5 Cleaning the watercraft ......4-6 Maintenance and adjustments ....4-7 Owner’s/Operator’s Manual and tool kit .............4-8 Periodic maintenance chart ....4-9 Inspecting the fuel system ....4-10 Inspecting the jet thrust nozzle angle .............4-12 Inspecting and adjusting the throttle...
It is advisable to have the watercraft serviced by a Yamaha dealer prior to stor- age. However, the following procedures can be performed by the owner. EJU11482...
1. Put the watercraft on land in a horizontal position. 2. Insert the garden hose adapter 2 into the flushing hose connector 1. 3. Connect the garden hose adapter to a water tap using a hose. NOTE: The garden hose is not included and must be purchased separately.
4. Install the cap securely. 5. Lubricate all cables such as the throttle, choke, and steering cables. NOTE: Use a Yamaha Power Cable Luber and Yamaha Lube-Zall to pressure lubricate the cables and purge out any moisture between the inner and outer cables.
EJU20600 Fuel system WARNING GASOLINE VAPORS HIGHLY FLAMMABLE AND EXPLOSIVE! Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition. Stop engine before refueling. Refuel in a well-ventilated area with the watercraft in a horizontal position. Do not stand or sit on the watercraft while refueling in case of fire.
Top off the fuel tank with fresh gasoline and add one ounce of Yamaha Fuel Stabi- lizer and Conditioner to each gallon of fuel. NOTE: Use of Yamaha Fuel Stabilizer and Condi- tioner eliminates the need to drain the fuel system.
12 volts. Specific gravity (for reference): 1.28 at 20 °C (68 °F) It is recommended to have a Yamaha dealer check the specific gravity and to charge the battery. If you maintain the battery yourself, be sure to read and follow the instructions provided with the battery tester and charger you use.
Remember that failures that are the result of the installation of parts or accessories which are not qualitatively equivalent to gen- uine Yamaha parts are not covered by the limited warranty. WARNING Be sure to turn off the engine when...
NOTE: A service manual is available for purchase through a Yamaha dealer for owners who have the mechanical skills, tools, and other equipment necessary to perform mainte- nance not covered by this Owner’s/Opera- tor’s Manual. EJU11501 Owner’s/Operator’s Manual and tool kit It is advisable always to carry the Owner’s/Operator’s Manual and tool kit with...
Check the fuel system for leaks, cracks, or malfunctions. If any problem is found, do the necessary repair or replacement as required. If repair is necessary, consult a Yamaha dealer. Check: Carburetor for leakage. Fuel pump for malfunction or leakage.
10 hours or first month of operation and every 200 hours or 24 months thereafter, or if water is found in the filter. Have a Yamaha dealer replace the fuel filter if necessary. WARNING Do not try to replace the fuel filter your- self.
Do not attempt to diagnose any problems yourself. Have a Yamaha dealer service the watercraft. Remove and inspect the spark plug peri- odically; heat and deposits will cause the spark plug to slowly break down and erode.
Lubrication points To keep moving parts sliding or rotating smoothly, coat them with water-resistant grease. Recommended water resistant grease: Yamaha Marine Grease/ Yamaha Grease A Throttle cable (carburetor end) Choke cable (carburetor end) Throttle cable (handlebar end) Pull the throttle lever and remove the seal 1.
Steering cable ball joint (nozzle end) Steering cable inner wire (nozzle end) Steering handle pivot shaft Lubrication of the steering handle pivot shaft requires disassembly of steering components. Have a Yamaha dealer lubri- cate it. Steering nozzle pivot bolts (collars) 4-15...
Intermediate housing Using a grease gun, fill the intermediate housing with water-resistant grease through the grease nipple. Grease quantity: Initial 10 hours or 1 month: 20.0–22.0 cm (0.67–0.74 oz) Every 100 hours or 12 months: 3.0–5.0 cm (0.10–0.33 oz) EJU01261 Adjusting the choke cable Check that the choke cable is properly adjusted.
EJU01971 Inspecting the battery Check the level of the battery electrolyte and make sure that the negative and posi- tive leads are securely tightened. WARNING Battery electrolyte is poisonous and dangerous, causing severe burns, etc. Electrolyte contains sulfuric acid. Avoid contact with skin, eyes, or cloth- ing.
CAUTION: Do not attempt to charge a battery hast- ily. Battery life could be shortened. It is recommended to have a Yamaha dealer charge the battery. If you charge the battery yourself, carefully read the battery charger instructions before charging and fol- low the points below.
Adjusting the carburetor The carburetor is a vital part of the engine and requires very sophisticated adjustment. Most adjusting should be left to a Yamaha dealer who has the professional knowledge and experience to perform it. However, the operator may adjust the trolling speed as part of the usual maintenance routine.
EJU01263 Replacing the fuse The fuse is in the electrical box 1. To replace the fuse: 1. Remove the cap 2, pull out the red lead, and bring the fuse holder 3 out of the electrical box. 2. Open the fuse holder and replace the fuse 4 with one of the correct amper- age.
EJU01305 Adjusting the jet thrust nozzle angle The angle of the jet thrust nozzle can be adjusted to suit operator preference. 1. Loosen the two screws, and then remove the steering pole cover 1. 2. Select the desired nozzle angle a. Changing the position of the handlebar stopper and/or steering cable pivot bolt changes the nozzle angle as shown in...
To change the position for the steering cable pivot bolt: 1. Pull back the outer sleeve, and then dis- connect the steering cable. 2. Remove the steering cable joint from the steering cable pivot bolt. 3. Loosen the pivot bolt and install it with the lock washer in the desired position (P1 or P2).
EJU01359 Specifications MODEL Unit SJ700 ITEM WATERCRAFT CAPACITY Maximum people on board Number of people DIMENSIONS Length mm (in) 2,240 (88.2) Width mm (in) 680 (26.8) Height mm (in) 660 (26.0) Dry weight kg (lb) 132 (291) PERFORMANCE Maximum power output kW (PS) @ r/min 53.7 (73) @ 6,300 Maximum fuel consumption...
If you have any trouble with your watercraft, use this section to check for the possible cause. If you cannot find the cause, or if the procedure for replacement or repair is not described in this Owner’s/Operator’s Manual, have a Yamaha dealer perform the necessary service. EJU01367 Troubleshooting chart...
Empty Refill as soon as possi- Engine runs irregu- larly or stalls Stale or contaminated Have serviced by 4-10 Yamaha dealer Too much oil in fuel Correct fuel-to-oil ratio mixing ratio to 50:1 Choke Knob is left pulled Push fully in...
CAUTION: Always avoid operating your watercraft in areas where weed growth is thick. If trav- eling in weeded areas is unavoidable, operate the engine alternately at partial throttle and full throttle. Weeds tend to accumulate more at a steady speed and at trolling speed.
EJU01882 Connecting the jumper cables 1. Connect the positive (+) jumper cable 1 to the positive (+) terminals of both bat- teries. 2. Connect one end of the negative (–) jumper cable 2 to the negative (–) termi- nal of the booster battery 3. 3.
EJU01895 Towing the watercraft If the watercraft becomes inoperative in the water, it can be towed to shore. If the watercraft must be towed in an emergency using a tow line, the operator should ride the watercraft, holding onto the handlebars and supporting his body weight on the riding tray.
EJU01907 Submerged watercraft If the watercraft is submerged or flooded with water, follow the procedure below and consult a Yamaha dealer as soon as possi- ble. Failure to do so may result in serious engine damage! In an emergency: 1. Beach the watercraft and remove the hood.
Owner’s/Operator’s Manual. The owner of the watercraft shall give notice to an authorized Yamaha dealer of any and all apparent defects within ten  days of dis- covery and make the watercraft available at that time for inspection and repairs at the dealer’s place of business.
If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new mailing address.
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.
EJU01125 Index Filling the fuel tank ........3-4 Fire extinguisher........3-9 2-stroke engine oil........3-2 Fishing vessel right-of-way....1-16 Flushing the cooling system ....4-1 Adjusting the carburetor ......4-19 Fuel and oil..........3-1 Adjusting the choke cable ..... 4-16 Fuel cock knob ........2-4 Adjusting the jet thrust nozzle angle ..
Reading buoys and other markers ..1-16 Watercraft characteristics......1-12 Recommended equipment ....1-11 Watercraft Education and Training..1-18 Replacing the fuse ........ 4-20 Water separator ........3-7 Rough water operation......3-31 Rules of the Road ......... 1-14 YAMAHA EXTENDED SERVICE Rules when encountering vessels..1-15 (Y.E.S.)............ 6-3...
YAMAHA MOTOR CORPORATION, USA Printed in Japan Jun. 2005—0.5 × 1 CR F1N-28199-14 Printed on recycled paper...