Related Manuals for Zanussi ZGF 6420
Summary of Contents for Zanussi ZGF 6420
- Page 1 GAS HOB ZGF 6420 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance...
-
Page 2: Important Safety Information
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation This appliance must be installed and serviced by a The chromed pan supports and burners will become competent person as stated in the Gas Safety discoloured over time. -
Page 3: Table Of Contents
Contents For the Installer For the User Important Safety Information Instructions for the Installer Description of the Hob Installation Operation Electrical Connections Maintenance and Cleaning Wiring Diagram Something Not Working? Fault Finding Service and Spare Parts Commissioning Customer Care Conversion from Natural Gas to LPG Guarantee Conditions European Guarantee Description of the Hob... -
Page 4: Operation
Operation Hob Burners " To light a burner: push in the relevant control knob and turn it anticlockwise to maximum position; then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. In the absence of electricity, ignition can occur without the electrical device;... -
Page 5: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. -
Page 6: Service And Spare Parts
Guarantee Conditions Zanussi Guarantee Conditions We, Zanussi, undertake that if, within 24 months of the Exclusions date of the purchase, this Zanussi appliance or any part This guarantee does not cover: thereof is proved to be defective by any reason only of... -
Page 7: European Guarantee
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed below for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: ·... -
Page 8: Instructions For The Installer
Instructions for the Installer Engineers Technical Data Overall dimensions Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Width: 580 mm Depth: 510 mm Front Left Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Cut out dimensions Rear Right Burner (semi rapid) Width: 560 mm... -
Page 9: Important Safety Requirements
Important safety requirements Location This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) The hob may be located in a kitchen, a kitchen/diner or and the IEE Wiring Regulations (Current Edition). bed sitting room, but not in a bathroom, shower room or For appliances installed in the Republic of Ireland please garage. -
Page 10: Installation
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. -
Page 11: Fitting The Hob Into The Worktop
Building In Building over a Cupboard or Drawer If the hob is to be installed above a cupboard or drawer it It is also recommended to carry out the electrical will be necessary to fit a heat resistant board below the connection to the hob as shown in diagrams 1 and 2. -
Page 12: Electrical Connections
Electrical Connections Permanent Connection Any electrical work required to install this hob should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations. -
Page 13: Wiring Diagram
Wiring Diagram 1. TAPS IGNITOR SWITCHES 2. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check SOCKET PLUG (with cover removed) (face view) Earth Wire Green/Yellow Brown Blue START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity check. Blue Green Brown... - Page 14 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse Light burner manually replace if necessary Check by pass Check polarity and simmer earth continuity of supply point Check position of the Check earth continuity electrode of appliance...
-
Page 15: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. - Page 16 CUSTOMER CARE Zanussi Major Appliances Addington Way Luton Bedfordshire LU4 9QQ © Electrolux plc 2003 35687-8602 04/06...