Download
Share
Print this page
  1. Manuals
  2. Brands
  3. PowerNet Manuals
  4. Network Router
  5. HomePNA3.0
  6. User manual

PowerNet HomePNA3.0 User Manual

Homepna3.0 (with 802.11g) adsl2+ firewall router
Hide thumbs

Advertisement

Quick Links

Download this manual
HomePNA3.0 (with 802.11g)
ADSL2+ Firewall Router
User's Manual
Version Release 1.04
8/15/2006

Advertisement

loading
Need help?

Need help?

Do you have a question about the HomePNA3.0 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for PowerNet HomePNA3.0

Summary of Contents for PowerNet HomePNA3.0

  • Page 1 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router User’s Manual Version Release 1.04 8/15/2006...

  • Page 2: Table Of Contents

    CHAPTER 1: INTRODUCTION ......................3 ......................3 NTRODUCTION TO YOUR OUTER ..............................3 EATURES CHAPTER 2: INSTALLING THE ROUTER ..................6 ....................6 MPORTANT NOTE FOR USING THIS ROUTER ..........................6 ACKAGE ONTENTS ............................7 RONT ............................8 ORTS ..............................8 ABLING CHAPTER 3: BASIC INSTALLATION ....................
  • Page 3 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router HomePNA ............................34 DHCP Server ..........................35 WAN (Wide Area Network) ......................... 36 ISP ..............................36 DNS ..............................44 ADSL.............................. 45 System ..............................46 Time Zone............................46 Remote Access..........................47 Firmware Upgrade.......................... 47 Backup / Restore..........................48 Restart Router ..........................

  • Page 4: Chapter 1: Introduction

    With the latest HomePNA3.0 technology, the router supports up to 128Mbps high-speed transmission rate for IPTV and Triple Play over the existing phoneline networking at home. The glossaries HomePNA and HPNA are synonyms.
  • Page 5 Users can utilize the existing phoneline network to enjoy ADSL WAN services. And adopt HomePNA3.0 that uses the in-house phone lines as Home Networking physical wiring LAN. Just connect the phoneline to the router, and you can extend high-speed applications without extra setting and new wiring.
  • Page 6 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to use the service, you must first apply for an account from a DDNS service like http://www.dyndns.org/.

  • Page 7: Chapter 2: Installing The Router

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Chapter 2: Installing the Router Important note for using this router Do not use this router in high humidity or high temperatures. Do not use the same power source for this router as other equipment.

  • Page 8: The Front Leds

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router The Front LEDs Meaning Power Lit when power is ON. Lit when the system is ready. Wireless Lit green when the wireless connection is established. (Wireless model only) Flashes when sending/receiving data. Lit when HPNA port is connected to other HPNA device(s) via in- house phoneline.

  • Page 9: The Rear Ports

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router The Rear Ports Port Meaning Power Switch Power ON/OFF switch PWR (DC 12V/1A) Connect the supplied power adapter to this jack. After the device is powered on, press it to reset the device or restore to factory default settings.

  • Page 10: Chapter 3: Basic Installation

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Chapter 3: Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The product provides a very easy and user-friendly interface for configuration.

  • Page 11: Connecting Your Router

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Connecting your Router Connect the Router to LAN (Local Area Network) and the splitter, then to in-house phoneline wiring (HPNA) and ADSL/telephone network. The splitter should specially support HomePNA band between Modem port and Phone port.

  • Page 12: Configuring Pc In Windows Xp

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuring PC in Windows XP Go to Start / Control Panel (in Classic View). In the Control Panel, double-click Network Connections. Double-click Local Area Connection. (See Figure 3.1) Figure 3.1: LAN Area Connection In the LAN Area Connection Status window, click Properties.

  • Page 13: Configuring Pc In Windows 2000

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuring PC in Windows 2000 Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and Dial-up Connections. Double-click Local Area (“LAN”) Connection. (See Figure 3.5) Figure 3.5: LAN Area Connection In the LAN Area Connection Status window, click Properties.

  • Page 14: Configuring Pc In Windows 95/98/Me

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuring PC in Windows 95/98/ME Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Configuration tab. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC.

  • Page 15: Configuring Pc In Windows Nt4.0

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuring PC in Windows NT4.0 Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Protocols tab. Select TCP/IP Protocol and click Properties. (See Figure 3.12) Figure 3.12: TCP / IP Select the Obtain an IP address from a DHCP server radio button and click OK.

  • Page 16: Factory Default Settings

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface (Username and Password) Username: Admin Password: Admin The default username and password are “Admin” and “Admin” respectively. If you ever forget the password to log in, you may press the RESET button up to 6 seconds to restore the factory default settings.

  • Page 17: Information From Your Isp

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA. Gather the information as illustrated in the following table and keep it for reference.

  • Page 18: Configuring With Your Web Browser

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 10.0.0.138, and click “Go”, a user name and password window prompt will appear. The default username and password are “Admin”...

  • Page 19: Chapter 4: Configuration

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Chapter 4: Configuration At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including: Status (ARP Table, Wireless Association Table(Wireless model only), Routing Table, DHCP Table,...

  • Page 20: Status

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Status The status page gives a global view of the router. ARP Table This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the MAC address of the network interface of your PCs to use with the router’s Firewall –...

  • Page 21: Wireless Association Table (Wireless Model Only)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router IP Address: A list of IP addresses of devices on your LAN (Local Area Network). MAC Address: The MAC (Media Access Control) addresses for each device on your LAN. Interface: The interface name (on the router) that this IP Address connects to.

  • Page 22: Dhcp Table

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router DHCP Table Leased: The DHCP assigned IP addresses information. Expired: The expired IP addresses information. Permanent: The fixed host mapping information Leased Table IP Address: The IP address that assigned to client. MAC Address: The MAC address of client.

  • Page 23: Homepna

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router HomePNA This page displays online HomePNA devices. Scan Endpoint : Scan the network of phoneline interface again and find the HomePNA endpoints. Tx Diagnose : Measure the transmitting signal quality from the router's HomePNA port to the related HomePNA device.

  • Page 24: Event Log

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Event Log This page displays the router’s Event Log entries. Major events are logged to this window, such as when the router’s ADSL connection is disconnected, as well as Firewall events when you have enabled Intrusion or Blocking Logging in the Configuration –...

  • Page 25: Diagnostic

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Diagnostic It tests the connection to computer(s) which is connected to LAN ports and also the WAN Internet connection. If PING www.google.com is shown FAIL and the rest is PASS, you ought to check your PC’s DNS settings is set correctly.

  • Page 26: Quick Start

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Quick Start For detailed instructions on configuring your WAN settings, please see the WAN section of this manual. Usually, the only details you will need for the Quick Start wizard to get you online are your login (often in the form of username@ispname), your password and the encapsulation type.
  • Page 27 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Select the desired option from the list and click Apply to return to the Quick Start interface to continue configuring your ISP connection. Please note that the contents of this list will vary, depending on what is supported by your ISP.

  • Page 28: Configuration

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuration When you click this item, you get following sub-items to configure the ADSL router. LAN, WAN, System, Firewall, QoS, Virtual Server, Time Schedule Advanced These functions are described below in the following sections.

  • Page 29: Ethernet

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Ethernet Primary IP Address IP Address: The default IP on this router. SubNetmask: The default subnet mask on this router. RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

  • Page 30: Ethernet Client Filter

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Ethernet Client Filter The Ethernet Client Filter supports up to 16 Ethernet network machines that helps you to manage your network control to accept traffic from specific authorized machines or can restrict unwanted machine(s) to access your LAN.

  • Page 31: Wireless (Wireless Model Only)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Wireless (Wireless model only) Parameters WLAN Service: Default setting is set to Enable. If you do not have any wireless, both 802.11g and 802.11b, device in your network, select Disable. Mode: The default setting is 802.11b+g (Mixed mode). If you do not know or have both 11g and 11b devices in your network, then keep the default in mixed mode.

  • Page 32: Wireless Security (Wireless Model Only)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Wireless Distribution System (WDS) It is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed simply define peer’s MAC address of the connected AP. WDS takes advantages...
  • Page 33 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router WEP Encryption: To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers highly secure data encryption, known as WEP. If you require high security for transmissions, there are two alternatives to select from: WEP 64 and WEP 128. WEP 128 will offer increased security over WEP 64.

  • Page 34: Wireless Client (Mac Address) Filter (Wireless Model Only)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Wireless Client (MAC Address) Filter (Wireless model only) The MAC Address supports up to 16 wireless network machines and helps you to manage your network control to accept traffic from specific authorized machines or to restrict unwanted machine(s) to access your LAN.

  • Page 35: Port Setting

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router You can easily by checking the box next to the MAC address to be blocked or allowed. Then, Add to insert to the Wireless Client (MAC Address) Filter table. The maximum Ethernet client is 16.

  • Page 36: Dhcp Server

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router DHCP Server You can disable or enable the DHCP (Dynamic Host Configuration Protocol) server or enable the router’s DHCP relay functions. The DHCP protocol allows your router to dynamically assign IP addresses to PCs on your network if they are configured to obtain IP addresses automatically.

  • Page 37: Wan (Wide Area Network)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router WAN (Wide Area Network) WAN refers to your Wide Area Network connection, i.e. your router’s connection to your ISP and the Internet. There are three items within the WAN section: ISP, DNS ADSL. The factory default is PPPoE. If your ISP uses this access protocol, click Edit to input other parameters as below.
  • Page 38 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account, sharing the single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.
  • Page 39 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Filter Type: Specify the type of ethernet filtering performed by the named bridge interface. Allows all types of ethernet packets through the port. Allows only IP/ARP types of ethernet packets through the port. Pppoe Allows only PPPoE types of ethernet packets through the port.
  • Page 40 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router characters (case sensitive). IP Address: Specify an IP address allowed to logon and access the router’s web server.. Note: IP 0.0.0.0 indicates all users who are connected to this router are allowed to logon the device and modify data.
  • Page 41 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router default setting for this command is enabled. Give DNSto Relay: Controls whether the PPP Internet Protocol Control Protocol (IPCP) can request the DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS server IP address, it automatically gives the address to the local DNS relay so that a connection can be established.
  • Page 42 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.
  • Page 43 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single ISP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.
  • Page 44 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Subnet Mask: sets the subnet mask used for the local IP interface connected to the PPP transport. If the value 0.0.0.0 is supplied, the netmask will be calculated from the class of the IP address obtained during IPCP negotiation.

  • Page 45: Dns

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router A Domain Name System (DNS) contains a mapping table for domain name and IP addresses. On the Internet, every host has a unique and user-friendly name (domain name) such as www.helloworld.com and an IP address. An IP address is a 32-bit number in the form of xxx.xxx.xxx.xxx, for example 10.0.0.138.

  • Page 46: Adsl

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router ADSL Connect Mode: The default setting is Multimode. This mode will automatically detect your ADSL line code, G.dmt, G.lite, and T1.413. But in some area, multimode cannot detect the ADSL line code well. If it is the case, please adjust the ADSL line code to G.dmt or T1.413 first. If it still fails, please try the other values such as ALCTL, ADI, etc.

  • Page 47: System

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router System There are six items within the System section: Time Zone, Remote Access, Firmware Upgrade, Backup/Restore, Restart User Management. Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network.

  • Page 48: Remote Access

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Remote Access To temporarily permit remote administration of the router (i.e. from outside your LAN), select a time period the router will permit remote access for and click Enable. You may change other configuration options for the web administration interface using Device Management options in the Advanced section of the GUI.

  • Page 49: Backup / Restore

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Backup / Restore These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mistakes.

  • Page 50: User Management

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router You may also reset your router to factory settings by holding the small Reset pinhole button on the back of your router in for 10-12 seconds whilst the router is turned on. User Management In order to prevent unauthorized access to your router’s configuration interface, it requires all users...

  • Page 51: Firewall And Access Control

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Firewall and Access Control Your router includes a full SPI (Stateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation.

  • Page 52: General Settings

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router General Settings You can choose not to enable Firewall, to add all filter rules by yourself, or enable the Firewall using preset filter rules and modify the port filter rules as required. The Packet Filter is used to filter packets based-on Applications (Port) or IP addresses.

  • Page 53: Packet Filter

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Packet Filter This function is only available when the Firewall is enabled and one of these four security levels is chosen (All blocked, High, Medium and Low). The predefined port filter rules in the Packet Filter must modify accordingly to the level of Firewall, which is selected.
  • Page 54 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Example: Predefined Port Filters Rules The predefined port filter rules for High, Medium and Low security levels are listed. See Table 1. (Note: Firewall – All Blocked/User-defined, you must define and create the port filter rules yourself.
  • Page 55 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Packet Filter – Add TCP/UDP Filter Rule Name: Users-define description to identify this entry or click to select existing predefined rules. Time Schedule: It is self-defined time period. You may specify a time schedule for your prioritization policy.
  • Page 56 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Packet Filter – Add Raw IP Filter Rule Name: Users-define description to identify this entry or click to select existing predefined rules. Time Schedule: It is self-defined time period. You may specify a time schedule for your prioritization policy.
  • Page 57 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Example: Configuring your firewall to allow for a publicly accessible web server on your LAN The predefined port filter rule for HTTP (TCP port 80) is the same no matter whether the firewall is set to a high, medium or low security level.
  • Page 58 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Click Delete Click Delete to delete the existing HTTP rule. Click Add TCP/UDP Filter. Click Add TCP/UDP Filter Input the Rule Name, Time Schedule, Source/Destination IP, Type, Source/Destination Port, Inbound and Outbound. Example: Application: Cindy_HTTP Time Schedule: Always On Source / Destination IP Address(es): 0.0.0.0...
  • Page 59 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router The new port filter rule for HTTP is shown below: Configure your Virtual Server (“port forwarding”) settings so that incoming HTTP requests on port 80 will be forwarded to the PC running your web server:...

  • Page 60: Intrusion Detection

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Intrusion Detection The router’s Intrusion Detection System (IDS) is used to detect hacker attacks and intrusion attempts from the Internet. If the IDS function of the firewall is enabled, inbound packets are filtered and blocked depending on whether they are detected as possible hacker attacks, intrusion attempts or other connections that the router determines to be suspicious.
  • Page 61 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router For SYN Flood, ICMP Echo Storm and ICMP flood, IDS will just warn the user in the Event Log. It cannot protect against such attacks. Table 2: Hacker attack types recognized by the IDS...

  • Page 62: Url Filter

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.abcde.com http://www.example.com) filter rules allow you to prevent users on your network from accessing particular websites by their URL. There are no pre-defined URL filter rules; you can add filter rules to meet your requirements.
  • Page 63 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Domains Filtering: This function checks the domain name only, not the IP address, in URLs accessed against your list of domains to block or allow. If it is matched, the URL request will be sent (Trusted) or dropped (Forbidden). For this function to be activated,...

  • Page 64: Firewall Log

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Andy selects both functions in the Domain Filtering and thinks that it will stop Bobby. But Bobby knows this function, Domain Filtering, ONLY disables all WEB traffic except for Trusted Domain, BUT not its IP address. If this is the situation, Block surfing by IP address function can be handy and helpful to Andy.

  • Page 65: Qos (Quality Of Service)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router QoS (Quality of Service) QoS function helps you to control your network traffic for each application from LAN (Ethernet and/or Wireless) to WAN (Internet). It facilitates you to control the different quality and speed of through put for each application when the system is running with full loading of upstream.
  • Page 66 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Destination Port: The destination port of packets to be monitored. Source IP Address Range: The source IP address or range of packets to be monitored. Destination IP address Range: The destination IP address or range of packets to be monitored.

  • Page 67: Outbound Ip Throttling (Lan To Wan)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Outbound IP Throttling (LAN to WAN) IP Throttling allows you to limit the speed of IP traffic. The value entered will limit the speed of the application that you set to the specified value’s multiple of 32kbps.

  • Page 68: Inbound Ip Throttling (Wan To Lan)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Inbound IP Throttling (WAN to LAN) IP Throttling allows you to limit the speed of IP traffic. The value entered will limit the speed of the application that you set to the specified value’s multiple of 32kbps.

  • Page 69: Example: Qos For Your Network

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Example: QoS for your Network Connection Diagram VoIP Normal PCs Restricted Information and Settings Upstream: 928 kbps Downstream: 8 Mbps VoIP User : 10.0.0.1 Normal Users : 10.0.0.2~10.0.0.5 Restricted User: 10.0.0.100 Throughput VoIP/VPN HIGH...
  • Page 70 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Mission-critical application Mostly the VPN connection is mission-critical application for doing data exchange between head and branch office. The mission-critical application must be sent out smoothly without any dropping. Set priority as high level for preventing any other applications to saturate the bandwidth.
  • Page 71 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Sometime your customers or friends may upload their files to your FTP server and that will saturate your downstream bandwidth. The settings below help you to limit bandwidth for the restricted application. Chapter 4: Configuration...

  • Page 72: Virtual Server ("Port Forwarding")

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Virtual Server (“Port Forwarding”) In TCP/IP and UDP networks a port is a 16-bit number used to identify which application program (usually a server) incoming connections should be delivered to. Some ports have numbers that are pre- assigned to them by the IANA (the Internet Assigned Numbers Authority), and these are referred to as “well-known ports”.
  • Page 73 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Time Schedule: A self-defined time period to enable your virtual server. You may specify a time schedule or Always on for the usage of this Virtual Server Entry. For setup and detail, refer to...

  • Page 74: Edit Dmz Host

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Edit: Click it to edit this virtual server application. Delete: Click it to delete this virtual server application. Using port forwarding does have security implications, as outside users will be able to connect to PCs on your network. For this reason you are advised to use specific Virtual Server entries just for the ports your application requires, instead of using DMZ.

  • Page 75: Edit One-To-One Nat (Network Address Translation)

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Disabled: As set in default setting, it disables the DMZ function. Enabled: It activates your DMZ function. Internal IP Address: Give a static IP address to the DMZ Host when Enabled radio button is checked.
  • Page 76 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Subnet: The subnet of the public/WAN IP address given by your ISP. If your ISP has provided this information, you may insert it here. Otherwise, use IP Range method. IP Range: The IP address range of your public/WAN IP addresses. For example, IP Address: 10.0.0.1, End IP: 10.0.0.10...

  • Page 77: List Of Some Well-Known And Registered Port Numbers

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router List of some well-known and registered port numbers. The Internet Assigned Numbers Authority (IANA) is the central coordinator for the assignment of unique parameter values for Internet protocols. Port numbers range from 0 to 65535, but only ports numbers 0 to 1023 are reserved for privileged services and are designated as “well-known ports”...

  • Page 78: Time Schedule

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Time Schedule The Time Schedule supports up to 16 time slots which helps you to manage your Internet connection. In each time profile, you may schedule specific day(s) i.e. Monday through Sunday to restrict or allowing the usage of the Internet by users or applications.

  • Page 79: Configuration Of Time Schedule

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Configuration of Time Schedule Edit a Time Slot Choose any Time Slot (ID 1 to ID 16) to edit, click Edit. Click Edit Note: Watch it carefully, the days you have selected will present in capital letter. Lower case letter shows the day(s) is not selected, and no rule will apply on this day(s).

  • Page 80: Advanced

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Advanced Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconfigure their router, unless advised to do so by support staff.

  • Page 81: Dynamic Dns

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Dynamic DNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is...

  • Page 82: Check Email

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Check Email This function allows you to have the router check your POP3 mailbox for new Email messages. The Mail LED on your router will light when it detects new messages waiting for download. You may also view the status of this function using the Status –...

  • Page 83: Device Management

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Device Management The Device Management advanced configuration settings allow you to control your router’s security options and device monitoring features. Embedded Web Server ( 2 Management IP accounts) HTTP Port: This is the port number the router’s embedded web server (for web-based configuration) will use.
  • Page 84 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Universal Plug and Play (UPnP) UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for the user to control advanced configuration of their device.
  • Page 85 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router The following MIBs are supported: From RFC 1213 (MIB-II): System group Interfaces group Address Translation group IP group ICMP group TCP group UDP group EGP (not applicable) Transmission SNMP group From RFC1650 (EtherLike-MIB): dot3Stats...

  • Page 86: Igmp

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router From RFC 1473 (PPP/IP MIB): PPP IP Group From RFC 1474 (PPP/Bridge MIB): PPP Bridge Group From RFC1573 (IfMIB): ifMIBObjects Group From RFC1695 (atmMIB): atmMIBObjects From RFC 1907 (SNMPv2): only snmpSetSerialNo OID IGMP IGMP, known as Internet Group Management Protocol, is used to management hosts from multicast group.

  • Page 87: Vlan Bridge

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router VLAN Bridge This section allows you to create VLAN group and specify the member. Edit: Edit your member ports in selected VLAN group. Create VLAN: To create another VLAN group. Advanced VLAN Setup Example (Triply Play)
  • Page 88 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Step 2: Create WAN Interface Go to Configuration wanlink is the factory default WAN interface which in service for data/internet access. If your ISP uses this access protocol, click Edit to input other parameters if needed. If your ISP does not use PPPoE, you can change the default WAN connection entry by clicking Change.
  • Page 89 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. Encapsulation method: Select the encapsulation format, this is provided by your ISP. Acceptable Frame Type: Specify what kind of traffic can through this connection, all traffic or only VLAN tagged.
  • Page 90 HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router To create another VLAN group for Video by clicking Create VLAN. Given a name and ID (PVID) to identify the Video group. The valid value range for PVID is 1 ~ 4094. From the example: VLAN untagged ports for Data/Internet: ethernet, wireless and wireless_wds.

  • Page 91: Save Configuration To Flash

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Save Configuration to Flash After changing the router’s configuration settings, you must save all of the configuration parameters to FLASH to avoid them being lost after turning off or resetting your router. Click Save to write your new configuration to FLASH.

  • Page 92: Chapter 5: Troubleshooting

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Chapter 5: Troubleshooting If the router is not functioning properly, first check this chapter for simple troubleshooting before contacting your service provider. Problems starting up the router Problem Corrective Action None of the LEDs are Check the connection between the adapter and the router.

  • Page 93: Problems With The Lan Interface

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router Problems with the LAN Interface Problem Corrective Action Can’t ping any PCs on Check the Ethernet LEDs on the front panel. The LED should be on for a the LAN. port that has a PC connected. If it is off, check the cables between your router and the PC.

  • Page 94: Appendix A: Product Support And Contact Information

    HomePNA3.0 (with 802.11g) ADSL2+ Firewall Router APPENDIX A: Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product.