Related Manuals for Siemens EC945RB90A
Summary of Contents for Siemens EC945RB90A
- Page 1 This cooktop is for use with Natural Gas and Universal LPG ER19350AU EC945RB90A Siemens - Electrogeräte GmbH Carl-Wery-Straß e 34 81739 München Cod. 9000271008 B...
- Page 3 Dear customer, We would like to thank and congratulate you for your choice. This practical modern appliance has been made using materials of the highest quality, which have been put through the strictest of Quality Controls during manufacture and meticulously tested to ensure that they meet all of your cooking demands.
-
Page 4: Table Of Contents
D. Terminal To change injectors E. Ignition module Injector size chart Minimum flame adjustment Operating instructions Burner location ER19350AU Burner ignition & control EC945RB90A Wok burner operation Si men User instructions Warnings concerning cooking U LPG Cleaning and maintenance Service 0,85... -
Page 5: Safety Considerations
Service Safety considerations It is not always necessary to call the Service Centre. In Trouble shooting some cases, you may be able to solve the problem chart yourself. This table contains some useful information. Important: For your safety • If the information in this manual is not followed exactly, a Only authorised personnel from the Service Centre are fire or explosion may result causing property damage, personal qualified to work on the main gas and electric systems. - Page 6 Cleaning and maintenance: Cleaning and maintenance: Cleaning and maintenance: 10. Important. When using a very large pot, leave a gap of at least 50 mm (2”) to avoid damaging any parts in bench top wood, plastic or other non-heat resistant materials. Never leave DON'Ts oil or hot fat unattended.
-
Page 7: Installation
Installation Warnings concerning cooking: Statutory DON'Ts This installation must conform with the following: requirements • Manufacturer’s Installation instructions • Local Gas Fitting Regulations Always use suitably sized • Municipal Building Codes, Do not use small recepta- receptacles on each bur- cles on large burners. -
Page 8: Clearances
Cooking Clearances A range hood fitted above the top must be installed recommendations according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a Very high /High Medium range hood and 750 mm for an exhaust fan. Wok burner Boiling, grilling, Reheating and keeping Any adjoining wall surface situated within 200mm from the... -
Page 9: User Instructions
User Instructions User Instructions Boiling burners Use “High flame” setting to bring the pan to the boil, then adjust the flame between “High flame” and “Low flame” to maintain the required pan temperature. Important: The use of a cooktop leads to the production of heat and moisture in the kitchen .For this reason make sure that the room is properly ventilated.Keep natural ventilation openings,... -
Page 10: Connection
Installation continued Wok burner operation Connection Electrical: An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical connection. The socket must remain The wok control has 4 settings. accessible after installation of the appliance. Important note: Largest flame =The outer and inner burners are both This appliance is connected to the mains (240 VAC) by means... -
Page 11: Operating Instructions
Operating instructions Burner locations There are two ways to carry out the connection to the main gas line: A. The hotplate can be connected with rigid pipe as specified in AS5601 table 3.1. B. Flexible Hose: If installing with a hose assembly, install with a hose assembly that complies with AS/NZS 1869 (AGA Approved), 10mm ID, class Bor D, no more than 1,2m long and in accordance with AS5601. -
Page 12: Service
Minimum flame adjustment. Coverting the cooktop To change injectors from Nat.Gas to 1 T urn the control knob to minimum. All work involved in installation, setting and adaptation Universal LPG to a different gas type must be carried out by authorised 2 Remove the control knob from the valve spindle.