1. Manuals
  2. Brands
  3. VEXILAR Manuals
  4. Marine Equipment
  5. EDGE 3
  6. Owner's manual

VEXILAR EDGE 3 Owner's Manual

Color lcd depth sounder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Edge
3
Color LCD
Depth Sounder
Model LC-507C
Owner's Manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EDGE 3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for VEXILAR EDGE 3

Summary of Contents for VEXILAR EDGE 3

  • Page 1 Edge Color LCD Depth Sounder Model LC-507C Owner’s Manual...

  • Page 2: Table Of Contents

    Higher frequencies have an advan- tage over lower frequencies for these reasons. Higher fre- quencies will also see small targets the low frequencies miss. Vexilar reserves the right to modify the features and specification described within this manual at any time and without notice.

  • Page 3: Specs & Features

    SPECS & FEATURES Separate Controls to Fine-Tune Each View Because the two sounders act so differently, separate controls allow Display: 16-Color 320 x 240 TFT (4-3/4” x 3-3/4”) you to make each show you what you want to see. For example, Frequency: 107 kHz &...

  • Page 4: Installation

    INSTALLATION MOUNTING THE TRANSDUCERS You will need to find a place to mount the unit that will make it The transducer mounting method will depend on which version easy to view and reach. You must provide the unit with power of the Edge you purchased.

  • Page 5: Electric Trolling Motor Transducer Installation

    line. Keep in mind that you need clear water flow across the face the reading, loosen the mounting screws and slide the transducer of the transducers to insure a clear reading at all speeds. Stay down slightly. Repeat these adjustments until you get a clear away from rivets, ribs, or strakes that would be just in front of reading.

  • Page 6: In-Hull Transducer Installation

    In-Hull Mounting towel or dry cloth to finish the clean-up of the areas. Let dry for a few minutes. Finding the best location for the transducers before mounting is critical. Choose a flat smooth spot near the center of the bilge Place the transducers exactly where you and near the back of the boat.

  • Page 7: Unit Operation

    UNIT OPERATION UNDERSTANDING THE DISPLAY The Edge is designed to be powerful, yet extremely easy to oper- In most situations, the Edge ’s display will be set up in the split ate. The first thing you’ll want to do is get familiar with the front screen mode with the 107 kHz beam on one side and the 400 kHz panel keys and their functions.
  • Page 8 OPERATION Left Beam Right Beam Beam Gain Level Auto Beam Frequency Beam Frequency Beam Gain Level Auto Current Range Scale Strong Left Beam Right Beam Signal Strength Key Water Surface Weak Temperature Battery Voltage Current Mode Clean Line Level Water Depth (Determined by Right (Left Beam) Screen)

  • Page 9: Control Panel Keys

    Current Mode - Shows the currently active mode (1 - 4) A / R - Push to toggle on and off the Automatic Range Control feature. When Auto-Range is on, an “R” will show at the top of Signal Strength Key - Shows the color verses signal strength for each beam display.

  • Page 10: Menu Functions

    MENU 2 The BEAM SELECT / C-LINE ADJ control also is used for navigation within the Edge ’s menus. The settings on this menu affect each mode, so only the currently active mode will retain the setting changes. Menu 2 is divided UNDERSTANDING THE MENU into two section.
  • Page 11 A-GAIN-LEVEL LEFT Automatic Gain Level configures how the system controls the This setting controls the frequency of the beam for the left side gain level when the Auto-Gain feature is on. “L” keeps the gain of the display, or to activate full screen mode. Full screen mode control on the lower side, “M”...
  • Page 12 MENU 3 A-GAIN-LEVEL Automatic Gain Level configures how the system controls the Menu 3 controls items such as the display color, zoom, and the gain level when the Auto-Gain feature is on. “L” keeps the gain temperature alarm. The settings on this menu affect all Modes. control on the lower side, “M”...
  • Page 13 Adjusting the Manual Zoom COMPOSITE To adjust the manual “zoom zone”, exit the menu and then use Composite mode places the 107 kHz beam and the 400 kHz beam the RANGE + and RANGE — keys for the left beam on the front on top of each other.
  • Page 14 MENU 4 DEPTH The Depth feature controls how the digital depth number appears The forth and final menu contains controls for some basic func- tions and unit of measure settings. at the bottom of the display. Your choices are OFF, S (Small), or L (Large).

  • Page 15: Accessories & Replacement Parts

    ACCESSORIES & REPLACEMENT PARTS TEMP-ADJ This feature allows you to calibrate the temperature reading, if Depth necessary. TBX071 107 kHz Transducer $79.00 To modify the temperature reading press... TBX072 400 kHz Transducer $79.00 MENU --> MENU --> MENU --> MENU (HOLD) CB0001 10’...

  • Page 16: Trouble Shooting

    Unit is turned on, but there is Contrast is adjusted too low. Address no display. Increase contrast. Vexilar, Inc. 6667 W Old Shakopee Road Unit runs well for a short time, Bad battery or poor connection. Minneapolis, MN, 55438 then the unit quits.

This manual is also suitable for:

Lc-507cEdge 3 lc-507c

Table of Contents