Tuner Operation; Basic Tuner Operation; Preset Tuning - Harman Kardon AVR 745 Owner's Manual

29510_AVR745_Engelsk 30/10/06

Tuner Operation

To change the remote room's volume, when
appears, press the OK/Enter
MULTI LEVEL
Button E on the TC 30 or the Set Button
Q on the ZR 10, and press the
tion Button DF to change the volume set-
ting. Note that this volume adjustment controls
the level for the output to the Multiroom
Audio Outputs and for any speakers con-
nected to the Surround Back/Multiroom
Speaker Outputs when the Surround Back
amplifier channels are configured for Multiroom
use, as shown on page 55. This adjustment does
NOT change the volume level for any room
where an ABUS module is used, as that setting is
only adjustable using the A-BUS module's vol-
ume control or built-in IR sensor.
Once the multiroom system is turned on, it will
remain on even if the AVR is placed in the
Standby mode in the main room by pressing the
Power Off Button 0 or the System Power
Control 2 on the front panel.
To turn the Multiroom system off from a remote
room using the ZR 10 remote, press the Power
Off Button A. To turn the Multiroom system
off from the remote room using the TC 30, press
the Devices Button 4 on the TC 30 remote
and then press the Screen Button 6 next to
AV Receiver. When the choices on the LCD
Screen 7 change, press the Page Left/Right
Buttons 8 once and then press the Screen
Button 6 next to
MULTI ROOM
OK/Enter Button E and then the
Navigation Buttons DF.

Basic Tuner Operation

The AVR's tuner is capable of tuning AM, FM and
FM Stereo broadcast stations and receiving RDS
data. Stations may be tuned manually, or they
may be stored as favorite station presets and
recalled from a 30 position memory.
• From the front panel, press the Input AM/FM
Button ! until the desired tuner frequency
band (AM, FM) appears. To change stations
within a frequency band, press the Tuning
Selection ).
9:32 Side 57
• From the TC 30 remote, press the Devices
Button 4 and then press the Screen
Button 6 to the left of
Naviga- . When the next page of options
/ INPUTS
⁄ ¤
appears on the LCD Screen 7, press the
Screen Button 6 to the left of
The tuner will become the active input and the
options on the LCD screen will become those
needed for tuner operation. Press the Screen
Button 6 next to any option to use it. For
example, press the Screen Button 6 next
to to change the frequency band. To
FM-AM
tune up or down through the current frequency
band, press the Screen Button 6 next to
TUNING U P
the tuner is the active device on the TC 30, the
Channel Up/Down buttons are used to change
station presets.
• To activate the IR command set used for
listening to FM radio, press the Activities
Button 3 and then press the Screen
Button 6 to the right of
.
F M RADIO
• To select the tuner from the ZR 10 remote,
press the Tuner Selector C.
• To change the tuning mode, press the Tune-M
Button O or the TC 30 Screen Button 6
next to
TUNE M
When the button is pressed so that
appears in the Main Information Display ˜
. Press the
each press of the Tuning Selectors ) will put
⁄ / ¤
the tuner in a scan mode that seeks the next
higher or lower frequency station with accept-
able signal strength. An
indication will momentarily appear when the sta-
tion stops at a stereo FM station, and an
indication will momentarily appear
TUNED
when an AM or monaural FM station is tuned.
Press the Tuning buttons again to scan to the
next receivable station.
When the button is pressed so that
appears in the Main Information Display ˜
each tap of the Selector will increased or
decrease the frequency by one increment. When
the tuner receives a strong enough signal for
adequate reception,
appear in the Main Information Display ˜.
• Stations may also be tuned automatically or by
entering the frequency. To enter a station's
frequency directly, first select the AM or FM
AUDIO
band as shown above. Next, press the Direct
Button M or the Screen Button 6 next
. to
TUNER
DIRECT I N
Line ˜, enter the station frequency by
pressing the Numeric Keys HG. The
desired station will automatically be tuned
after the latest number is entered. If you press
an incorrect button while entering a direct
frequency, press the Clear button L to start
over.
or . When
TUNING DOWN
NOTE: When the FM reception of a stereo stati-
on is weak, audio quality will be increased by
switching to Mono mode by pressing the Tuner
Mode button I on the remote or holding the
Band Selector O! on the front panel so
that
Main Information Display ˜ and then goes
out.
LISTEN T O

Preset Tuning

Using the remote, up to 30 stations may be
stored in the AVR's memory for easy recall using
the front panel controls or the remote.
To enter a station into the memory, first tune the
.
station using the steps outlined above. Then:
AUTO
1. Press the Memory Button N on the ZR 10
remote; the station's frequency will flash or press
the Screen Button 6 next to
2. Within five seconds, press the Numeric
Keys GH corresponding to the location
AUTO S T TUNED
where you wish to store this station's frequency.
Once entered, the preset number will appear in
AUTO
the Main Information Display ˜.
3. Repeat the process after tuning any additional
stations to be preset.
Recalling Preset Stations
MANUAL
• To manually select a station previously entered
in the preset memory, press the Numeric Keys
GH that correspond to the desired station's
memory location.
• To manually tune through the list of stored pre-
will
MANUAL TUNED
set stations one by one, press the Preset
Stations Selector buttons # on the front
panel. The Prev/Next Transport Controls P
on the ZR 10 remote, or the Channel Up/Down
Buttons G on the TC 30 remote control when
the tuner is the active input device.
. Within 5 seconds of when
DIRECT
scrolls in the Upper Display
appears momentarily in the
MANUAL
MEMORY
TUNER OPERATION 57
.