Output Level Adjustment - Harman Kardon AVR 110 Owner's Manual

System Configuration
7. When you have completed your selection
for the center channel, press the Set
button o
Ô , and then press the
buttons n
30 on the remote or
‹ / ›
the Selector buttons 5 on the front
panel to change the display to SUR
SPEAKER.
8. Press the Set button t
again, and
Ô
buttons mq on the
then use the
⁄ / ¤
remote or the Selector buttons 5 on the
front panel to select the option that best
describes your system based on the speaker
definitions shown in preceding section.
When SUR SMALL is selected, low-fre-
quency surround-channel sounds will be
sent to the subwoofer output only. Note
that if you choose this option and there is
no subwoofer connected, you will not hear
any low-frequency sounds from the sur-
round speaker.
When SUR LARGE is selected, a full-
range output will be sent to the surround-
channel outputs, and NO surround channel
signals will be sent to the subwoofer
output.
When SUR NONE is selected, surround-
sound information will be split between
the front-left and front-right outputs. Note
that for optimal performance when no sur-
round speakers are in use, the Dolby 3
Stereo mode should be used instead of
Dolby Pro Logic.
9. When you have completed your selection
for the surround channel, press the Set
button o
Ô , and then press the
buttons mq on the remote or the
Selector buttons 5 on the front panel to
change the display to S-W SPEAKER.
10. Press the Set button o
Ô , and then
buttons mq on the
press the
⁄ / ¤
remote or the Selector buttons 5 on
the front panel to select the option that
best describes your system.
The choices available for the subwoofer
position will depend on the settings for the
other speakers, particularly the front left/right
positions.
18 SYSTEM CONFIGURATION
If the front left/right speakers are set to
SMALL, the subwoofer will automatically be
set to SUB, which is the "on" position.
If the front left/right speakers are set to
LARGE, three options are available:
• If no subwoofer is connected to the
AVR 110, press the
on the remote so that SUB NONE
appears in the Main Information
Display W. When this option is selected,
all bass information will be routed to the
front left/right "main" speakers.
• If a subwoofer is connected to the AVR 110,
you have the option to have the front
left/right "main" speakers reproduce bass
frequencies at all times, and have the sub-
woofer operate only when the AVR 210 is
being used with a digital source that con-
tains a dedicated Low-Frequency Effects, or
LFE, soundtrack. This allows you to use both
your main and subwoofer speakers to take
advantage of the special bass created for
certain movies. Press
on the remote so that SUB (LFE)
appears in the Main Information
Display W.
• If a subwoofer is connected and you wish to
use it for bass reproduction in conjunction
with the main front left/right speakers,
regardless of the type of program source or
surround mode you are listening to, press
buttons mq on the remote
the
⁄ / ¤
so that SUB L/R+LFE appears in
the Main Information Display W.
When this option is selected, a "complete"
feed will be sent to the front left/right
⁄ / ¤
"main" speakers, and the subwoofer will
receive the bass frequencies under frequen-
cy selected in the next option setting on this
menu, as described below.
11. When all speaker selections have been
made, press the Set button o
return to normal operation.

Output Level Adjustment

Output level adjustment is a key part of the
configuration process for any surround-sound
product. It is particularly important for a Dolby
Digital receiver such as the AVR 110, as correct
outputs will ensure that you hear sound tracks
in their proper place with the proper direction-
ality and intensity.
IMPORTANT NOTE: Listeners are often con-
fused about the operation of the surround
channels. While some assume that sound
should always be coming from each speaker,
most of the time there will be little or no
sound in the surround channels. This is because
they are only used when a movie director or
sound mixer specifically places sound there to
buttons mq
create ambiance, a special effect or to continue
⁄ / ¤
action from the front of the room to the rear.
When the output levels are properly set it is
normal for surround speakers to operate only
occasionally. Artificially increasing the volume
to the rear speakers may destroy the illusion
of an enveloping sound field that duplicates
the way you hear sound in a movie theater or
concert hall.
Before beginning the adjustment process make
certain that all speaker connections have been
properly made. The system volume should be
set to the level that you will use during a typi-
cal listening session. Finally, make certain that
the Balance Control * is set to the center
"12 o'clock" position.
buttons mq
⁄ / ¤
To assist in making speaker configuration set-
tings, the icons in the Speaker/Channel
Input Indicators O change as the speaker
type is selected at each position. When only the
center icon box containing the abbreviation for
the speaker position is lit, the speaker is set for
"small. " When the inner box and the two outer
boxes with circles inside them are lit, the speak-
er is set for "large. " When no indicator appears
at a speaker location, that position is set for
"none" or "no" speaker.
For example, in the following figure, the left
front and right front speakers are set for
"large, " the center, left surround (LS) and right
surround (RS) speakers are set for small, and a
subwoofer is set, as shown by the box with the
abbreviation "LFE", which stands for "low-fre-
quency effects. "
Ô to
L C R
LFE
LS RS