Advertisement
I Setting Up
1.
Assemble the KP120. As shown in the
illustrations, remove the wing bolts and
attach the riser and legs. Use the tuning
key to loosen the adjustment bolts, then
extend the four legs and tighten the bolts
loosely.
2.
Attach your foot pedal to the KP120.
Adjust the legs so that the surface of the
KP120's pad is vertical when the foot
pedal is attached and the kick pad and
pedal are stable when the pedal is used
to strike the pad. After leg length has been
determined, tighten the bolts firmly to
secure.
I Troubleshooting
If the following trouble occurs when the KP120 is used, please check the following points
before asking your dealer for assistance.
G No sound output, sound level is low
Problem
Is the KP120's OUTPUT jack properly connected
to the INPUJT jack of the DTXTREME/DTX/
DTXPRESS with the supplied cable?
Is the KP120's Level Adjustment Knob set lower
than necessary?
Is the DTXTREME/DTX/DTXPRESS properly con-
nected to an external device such as a pair of head-
phones, amplifier, speaker, etc?
Is the DTXTREME/DTX/DTXPRESS properly
setup?
G Multiple sounds are produced when the pad is struck once (Double Trigger).
Problem
Is the KP120's Output LEVEL adjustment knob
set too high?
Is the Input Pad Type to which the KP120 is con-
nected to the DTXTREME/DTX/DTXPRESS set
to a pad type other than "RH Kick" on the
DTXTREME, "pad 2" on the DTX, or "KP" on the
DTXPRESS?
❇ If the double triggers continue even after you have tried the solutions listed above, use the DTXTREME/DTX/
DTXPRESS "Self Rejection" function to control the problem. Refer to the Owner's Manual supplied with the
DTXTREME/DTX/DTXPRESS for more information.
For more information on the problems listed above and other problems, please refer to the "Owner's
Manual" of the DTXTREME/DTX/DTXPRESS. If you cannot solve the problem on your own, please contact
the dealer from whom you purchased the device.
* A drum tuning key will be required for assembly.
Wing Bolt for
Wing Bolt for
Legs
Legs
Washer
Washer
Washer
Washer
Spring Washer
Spring Washer
Wing Bolt for Riser
Loosen
Adjustment
Bolt
Legs
Riser
Beater
Leg Rubber
Non-Slip Spur
What to check.
Check the connections between the KP120 and the
DTXTREME/DTX/DTXPRESS.
When the Level Adjustment Knob is set lower than nec-
essary, even though the pad may have been hit hard,
only a weaker signal is sent so the tone generator in the
DTXTREME/DTX/DTXPRESS will not be able to pro-
duce sufficient volume.
Check the connections between the external devices
and also the power switch, volume, etc. settings on the
external device.
Make sure the volume setting assigned to the INPUT
number on the DTXTREME/DTX/DTXPRESS to which
the KP120 is connected is not set too low (refer to the
previous "Increase the Volume" section) or the
headphone's volume is set too low.
What to check.
If the Output LEVEL knob is set too high, the large sig-
nal remains for a longer time causing the DTXTREME/
DTX/DTXPRESS to produce multiple triggers. Use the
previously explained Output LEVEL adjustment to set
the level to a proper level.
Even if the signal level is the same, if the pad type is set
t o a d i f fe r e n t p a d t y p e , d o u b l e t r i g g e r s
might easily occur. Refer to the Owner's Manual sup-
plied with the DTXTREME/DTX/DTXPRESS
for more information.
3.
Make slight adjustments to the pedal's position and the beater length so that beater strikes
the pad at its center.
Beater
NOTE : A double foot pedal setup (YAMAHA: DFP-880, etc.) can also be used. When a double foot pedal setup is
used on the KP120, the position of the pedal and length of the beaters should be adjusted so that the point
between the two beaters is positioned at the pad's center.
NOTE : Use the legs with their non-slip spurs at the ends of the legs exposed, if the drum is setup on a platform or
marks on the floor are no problem. If you don't want to leave marks on the floor, use the legs with the spurs
at the ends of the legs covered with the rubber ends.
NOTE : Drum head tension can be adjusted by tightening or loosening the tuning bolts on the hoop with a drum key.
Extend
However, there will be no change in the tone produced by the DTXTREME/DTX/DTXPRESS, etc.
NOTE : Please make sure that head tension is even all the way around the head. Uneven tension may produce
wrinkles, which may shorten the life of the drum head.
NOTE : Never tighten or loosen the drum head more than necessary. Over tightening may result in damage to the
drum head, shell, etc. An overly loosened head may result in a shorter life of the drum head, cushion, or noise.
I Connections
Use the supplied monaural phone cable to con-
nect the pad's OUTPUT jack to the Input (KICK,
e t c . ) j a ck o n t h e D T X T R E M E / D T X /
DTXPRESS. Connect the cable's L-shaped
plug to the pad.
NOTE : When the KP120 is used with the DTXTREME/
DTX/DTXPRESS, please set the INPUT's "Pad
Type" setting to "RH Kick" on the DTXTREME,
"pad 2" on the DTX, or "KP" on the DTXPRESS.
Selecting another pad type may result in
problems such as double triggers (when a single
stroke produces multiply triggered sounds). Please
refer to the "Owner's Manual" supplied with your
DTXTREME/DTX/DTXPRESS.
I Specifications
Pad Diameter
Size (when setup including protrusions) 530(W)x330(D)x510(H)mm
Weight
Sensor System
Control
Output Jack
Accessories
* Improvements may result in a change in the specifications and/or design of the product without notice.
NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the
manufacturer's warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the
production methods used to produce them, meet these goals. In keeping with both the letter and the spirit of the law, we want you to be aware of the following:
Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is
approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.
This product may also use "household" type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that
the charger is intended for the battery being charged.
When installing batteries, do not mix batteries with new, or with batteries of a different type. Batteries MUST be installed correctly. Mismatches or incorrect installation
may result in overheating and battery case rupture.
Warning: Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the
laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.
Disposal Notice: Should this product become damaged beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.
NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate.
You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.
Model
Purchase Date
Beater (Double Pedal)
3m Cable with Standard Phone
Plug (monaural)
12 inches
5,310g
Single Trigger Type
Output LEVEL Volume x1
Standard Monaural Phone Jack
Monaural Phone Cable (3m) x1, Owner's Manual (this booklet) x1
SPECIAL MESSAGE SECTION
Serial No.
PLEASE KEEP THIS MANUAL
Hoop
Tuning Bolt
Connect
Advertisement
