Epson product. Epson is not responsible for any use of this information as applied to other products. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to...
Contents Introduction Projector Parts Remote Control Optional Accessories Registration and Warranty Using This Manual Setting Up the Projector Choosing a Location Installing the Projector Connecting the Cables Connecting Video and Computer Equipment Making Other Connections Installing Batteries in the Remote Control Turning the Projector On and Off Turning On the Projector Turning Off the Projector...
Page 4
Making Detailed Adjustments Using the Menu System Changing How the Menus Display Adjusting the Picture Quality Input Brightness Settings Sharpness and Picture Quality Settings Color Settings Adjustments for Computer Images Selecting Memory Settings and Resetting the Projector Selecting Memory Settings Creating Memory Settings Deleting Saved Memory Settings Resetting the Projector...
Page 5
Specifications General Lamp Remote Control Dimensions Electrical Environmental Safety Compatible Video Formats ESC/VP21 Command Codes Notices Important Safety Information FCC Compliance Statement Declaration of Conformity Epson America, Inc. Limited Warranty Index Contents...
Auto Iris system that constantly controls the light output based on the gamma and black/white levels of your projected content, for perfectly adjusted images and deepest blacks ■ ™ Epson C Fine 3LCD technology for reliable picture quality, increased contrast ratio and uniform colors ■...
Projector Parts Front Control panel (top) Vertical lens shift dial Lamp cover Control panel (side) Zoom ring Ventilation slots Infrared receiver Adjustable foot Horizontal lens shift dial Adjustable foot Focus ring Lens cover Back Infrared receiver Component Control (RS-232C) port video port PC port S-Video port...
Bottom Mounting bracket attachment points Optional cable cover attachment points (brass colored) Projector Control Panel Top control panel Side control panel Menu navigation button Power button Source button Switches the video input source Menu button Enter button Esc button Warning lights Displays the Selects menu items or Exits the current...
Remote Control Power button Turns projector on or off Illumination button Lights the remote control buttons for easy viewing Source buttons Switches between equipment connected to the projector Default button Restores default settings when menu is displayed Esc (escape) button Exits the current menu item Enter/Line Menu button Selects menu items or opens...
Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada. See your Extra Care Home Service brochure for details.
Note: Contains important information about your projector. Tip: Contains helpful projection tips. Need additional help? Take advantage of Epson’s automated support services 24 hours a day at epson.com/support (U.S.) or epson.ca/support (Canada). Use this site to view FAQs (Frequently Asked Questions) or product information and e-mail your questions to Epson support.
Setting Up the Projector Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image. Choosing a Location You can install the projector for the viewing setups shown below, as well as rear projection. Center Side Ceiling...
Page 13
Ideally, keep the projector level and place it at a height so its lens is centered between the top and bottom of the screen, as shown below. If this is not possible, use the lens shift dials to reposition the image. As a rule of thumb, you can use lens shift to move the image up or down by nearly its full height, and left or right by about one-half its width (for details, see page 25).
Page 14
The size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how you use the Zoom ring, the actual size may differ. Use these tables as a guide for projector placement: 16:9 aspect ratio Diagonal image size Horizontal...
Page 15
To determine the exact image size when you know the projection distance (or the exact projection distance when you know the desired image size), you can use the Image Size Calculator. This program is available on the Epson website at epson.com/support (U.S.) or epson.ca/support (Canada).
Front/Ceiling 4. Press the button when done. Menu Note that you can rotate the Epson logo plate 180 degrees when suspending the projector from a ceiling. If you are planning to use an AV controller with the projector, refer to the table of ESC/VP21 command codes on page 67.
Page 17
The following illustrations show the dimensions of the projector: Center of lens 5.4 in. 5.8 in. 148.3 mm 2.8 in. 72 mm 0.2 in. 0.5 in. 4.5 mm 12.3 5.2 in. 131 mm 17.7 in. 450 mm 11.8 in. 3.0 in. 300 mm 75 mm 5.9 in.
Connecting the Cables Connecting Video and Computer Equipment You can connect the projector to many types of video equipment, such as a Blu-ray ™ Disc /DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple Macintosh system. For details on compatible video formats, see page 65.
Page 19
For best results, connect your video equipment to the port, if possible. If your HDMI equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first): (for component video), , or (for composite video). Component S-Video Video Connect video equipment to one...
Making Other Connections Connect the power cable and other cables described below, depending on how you plan to use the projector. ■ Plug the power cable into the projector and a grounded electrical outlet. ■ port outputs a 12-volt DC signal Trigger out when the projector is turned on.
Installing Batteries in the Remote Control The remote control uses two AA batteries. WARNING: Keep batteries away from children. If a battery is swallowed, contact your doctor immediately. 1. Release the tab and lift open the cover. 2. Insert two new AA batteries as shown. 3.
4. Press the Ppower button on the remote control or projector. Remote control Projector Note: To prevent children from turning on the projector, you can use the Child Lock feature. See page 32 for details. If you’ll be using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool the projector at the high altitude air pressure.
Selecting the Image Source The source buttons on the projector and remote control let you switch between images from different pieces of equipment connected to the projector (such as a Blu-ray Disc/DVD player, cable or satellite box, or video game console). Press the button on the remote control that corresponds to the port to which your Source...
Positioning the Image If the image is not centered on the screen, use the horizontal and vertical lens shift dials to adjust its position. Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position.
Page 25
The image cannot be moved to the maximum distance in both the vertical and horizontal directions. For example, the image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9 percent of the width of the image.
Making Basic Adjustments Follow the instructions in this chapter to make basic adjustments to the image shape, size, color, and quality. For further refinements, see “Making Detailed Adjustments” on page 33. Focusing and Zooming Use the focus ring to sharpen the image. Use the zoom ring to reduce or enlarge the image.
Choosing the Aspect Ratio In many cases, video signals are automatically resized to fit on your screen when is selected as the Aspect setting. Auto Aspect You may need to change the size of the image (or aspect button ratio) for certain image types by pressing the button Aspect on the remote control.
■ x.v.Color for the most natural color reproduction when viewing movies through HDMI. The built-in Epson Cinema Filter automatically improves color reproduction in a darkened room; it is not used when you select Dynamic Living Room...
Advanced Color Adjustments To further customize the color and image quality, you can adjust the gamma and individual RGBCMY color tones using the buttons on the remote control (not RGBCMY Gamma available when is selected as the Color Mode). x.v.Color RGBCMY Gamma Note: You can fine-tune these and other color and image quality settings using the projector’s...
Adjusting the Gamma Setting You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas. Higher values will darken the light areas. Gamma presets make minor adjustments to mid-tone values.
Adjusting RGBCMY Use this feature to adjust the hue, saturation, and brightness for each of the red (R), green (G), blue (B), cyan (C), magenta (M), and yellow (Y) color components. Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28). 1.
Locking the Projector The projector includes two lock settings to prevent the image from being accidentally changed once it’s adjusted, and to keep children from turning on the projector without adult supervision. To access the lock settings, follow these steps: Menu navigation 1.
Making Detailed Adjustments You can use the projector’s on-screen menus to make detailed adjustments to the image quality—such as the brightness, contrast, sharpness, and color. You can also change the menu display, sleep mode settings, and other projector features. Using the Menu System You can access the menu system either from the remote control or the buttons on the projector’s control panel.
Page 34
3. Press the u, d, l, or r button to change settings as necessary. You may have to press the button to confirm your choice. Enter 4. When you’re finished, press the button to return to the previous menu or press the button to exit the menu system.
Changing How the Menus Display Use these options to control how the menus display. ■ Language Settings > Language Select from 21 languages to use in the menu system. ■ Menu Position Settings > Display > Menu Position Use the arrow buttons to choose a position on the screen for displaying the menu. ■...
Page 36
■ EPSON Super White Signal > Advanced > EPSON Super White Note: This setting can be used only when the signal is input through the HDMI 1 or HDMI 2 ports with the Color Mode set to Natural or Cinema (see page 28).
■ HDMI Video Range Signal > Advanced > HDMI Video Range Note: This setting can be used only when HDMI 1 or HDMI 2 is selected as the image source (see page 23). This setting cannot be used when the Color Mode is set to x.v.Color (see page 28).
■ Progressive Signal > Progressive Note: This setting can be used only when viewing composite video or S-video signals, or 480i, 576i, or 1080i signals input through the Component, HDMI 1, or HDMI 2 ports (see page 65). ™ Converts interlaced to progressive signals. The projector uses 3D DigiScan Circuitry Processing for video-sourced images.
Color Settings If the image colors don’t look correct, you can adjust them using these settings. Use the first three settings described below to make the most visible changes. If you only need to make slight adjustments, you can fine-tune the picture with the remaining settings. Most color settings are stored separately for each image source and color mode.
Page 40
■ RGB Image > Advanced > RGB Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28). Use the RGB settings to fine-tune the color of the image. You can adjust the offset and gain for each signal color (red, green, and blue).
Adjustments for Computer Images In addition to the settings described previously, you can adjust the Tracking and Sync settings for analog RGB computer images. Normally, these settings are adjusted automatically by the projector. If you notice that the image is blurry or contains dark vertical bands, you may need to adjust the settings yourself.
Selecting Memory Settings and Resetting the Projector Your projector comes with 10 memory locations where you can save customized settings to obtain the best picture quality for each of your video inputs. Selecting Memory Settings You can easily recall the memory settings by using the Memory memory button on the remote control.
Deleting Saved Memory Settings You can clear all your memory settings at once. 1. Press the button on the remote control. Menu 2. Open the menu, then select Reset Reset Memory 3. Select , then press the button to delete the memory settings. Enter Note: You can delete memory settings one at a time with the Erase Memory setting under the Memory menu.
3. Do one of the following: ■ Select to clear the lamp usage timer and reset it to zero. Reset Lamp Hours You should reset the lamp timer only when you install a new projector lamp. See page 54 for more information. ■...
■ Zoom Size Signal > Zoom Size Lets you reduce the image size in the vertical direction so that the top and bottom of the image are visible (available only if the aspect ratio has been set to Zoom ■ Zoom Caption Pos. Signal >...
■ Direct Power On Settings > Direct Power On Sets projection to start when the main power switch is turned on, without pressing the P power button on the remote control or the projector. Note: When direct power on is enabled, power surges that occur after a power outage can cause the projector to turn on.
■ Child Lock Settings > Child Lock Lets you lock the Ppower button on the projector’s control panel to make it more difficult for a child to turn on the projector. See page 32 for more information. ■ Control Panel Lock Settings >...
Maintenance Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. You also may need to clean the air filter to prevent overheating. WARNING: Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers.
Cleaning the Projector Case Before you clean the case, turn off the projector and unplug the power cord. ■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent.
Page 50
If the dirt is difficult to remove or the filter is broken, replace it. You can purchase air filter part number V13H134A21 from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Turn off this product when not in use to prolong the life of the projector. You can purchase lamp part number V13H010L49 from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S.
Page 52
5. Insert the screwdriver that came with the lamp (or a similar tool) into the slot on the back of the projector to release the lamp cover. Then lift up the cover to remove it. 6. Loosen the two screws securing the lamp (they don’t come all the way out). 7.
Page 53
8. Gently insert the new lamp and tighten its screws. Caution: Don’t touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 9. Replace the lamp cover. (The projector won’t work if the lamp cover is open or loose.) 10.
Resetting the Lamp Usage Timer After replacing the lamp, plug the projector back in, turn on the power switch on the back, and press the Ppower button. Then follow these steps to reset the lamp usage timer: 1. Press the button on the projector or remote control.
Pack the projector in its original packaging or equivalent. Transporting the Projector Note: Epson shall not be liable for any damages incurred during transportation. The projector contains many glass and precision parts. When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials.
Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Come On or Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
Page 57
There is an internal problem. Turn off the power switch on the lights are flashing back of the projector, and unplug it from the electrical outlet. Then contact Epson for assistance (see page 62). The temperature There is a fan or sensor problem. Turn off the power switch on light flashes red the back of the projector, and unplug it from the electrical outlet.
Solving Picture Problems You cannot turn on the projector. ■ Make sure the power cord is connected and the power switch in back of the projector is turned on. Then wait a moment for the Ppower light to come on before pressing the Ppower button.
Page 59
You’re using a computer and no picture appears on the screen. ® If you’re using a Windows laptop: ■ Press the function key that lets you display on an external monitor. It’s often labeled with an icon such as , but it may also be labeled .
Page 60
The picture isn’t rectangular. ■ If the image looks like , the projector has been placed off to one side of the screen and angled toward it. Face the projector straight ahead (instead of at the center of the screen), then use the horizontal lens shift dial to center the image (see page 24). ■...
■ Fine-tune the colors with the settings listed on page 39. ■ If the picture looks dark, you may need to replace the lamp. Check the lamp usage timer to see how long the lamp has been in use (see page 54). Replace the lamp if it’s close to the end of its service life (see page 51).
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6...
Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels 0.74 inch (18 mm) wide Lens F=2.0 to 3.17 Resolution (native format) 1920 × 1080 pixels, 1080p Brightness Normal mode: White light output 1800 lumens (ISO 21118 standard) Color light output 1800 lumens Dynamic contrast ratio 25000:1...
Dimensions Height 5.4 inches (136 mm), not including adjustable feet Width 17.7 inches (450 mm) Depth 14.2 inches (360 mm); not including lens protrusion Weight 16.1 lb (7.3 kg) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC: 3.1 A 200 to 240 VAC: 1.3 A Power consumption 100 to 120 VAC:...
Compatible Video Formats The projector supports analog video in NTSC, PAL, and SECAM formats, and it automatically adjusts to the incoming signal. It can receive these formats as composite video, S-video, or component video— which it accepts through the Video, S-Video, and Component ports, respectively. The projector also supports digital video (SDTV, HDTV) and various monitor display formats.
You can use an AV controller with a 9-pin null modem serial cable to control the projector. You can download the complete ESC/VP 21 Communication Manual for home theater projectors from the Epson website at epson.com/support (U.S.) or epson.ca/support (Canada). Following are some of the available codes:...
Notices Important Safety Information Follow these safety instructions when setting up and using the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. ■...
Page 69
■ The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. ■ Allow the lamp to cool for one hour before replacing it. ■ Unplug the projector during lightning storms or when not in use for extended periods. ■...
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
What Epson Will Do To Correct Problems: If your product requires service during the limited warranty period, please call Epson at the number on the bottom of this statement and be prepared to provide the model, serial number, and date of original purchase. Epson will, at its option, repair or replace the defective unit, without charge for parts or labor.
Page 72
Epson product for carry-in warranty service are your responsibility. Epson will pay for all freight charges if you choose to send your unit to Epson for repair. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred.
Page 76
Trigger out setting, 46 Turning on and off projector, 21 to 22, 58 Video Signal setting, 46 Video, compatible formats, 65 to 66 VP21 codes, 67 Warranty, 10, 71 to 72 Where to Get Help, 62 Wide setting, 27 x.v.Color setting, 28 Zoom Caption Pos.