Page 2
Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference.
Important safety information This section includes safety information that • Items cleaned or washed with gasoil/fuel oil, will help protection from risks of personal dry-laundry solvents and other combustible injuries or materialistic damages. Failure or explosive materials as well as the items to follow these instructions shall cause that are contaminated or spotted with such any warranty and reliability commitment to...
• Do not reach into the machine when the disorders or unlearned or inexperienced drum is spinning. people (including children) unless they • Unplug the machine when it is not in use. are attended by a person who will be •...
Installation Refer to the nearest Authorised Service Agent washing machine. The bracket (Part no. for installation of your product. 296 280 0100 white/296 280 0200 grey) Preparation of location and electrical must be installed by the Authorised Service installation for the product is under Agent.
Page 6
Important: The ventilation hose should not be • The hose should be attached to a height of connected to the chimney of a stove or a maximum 80 cm. fireplace. • Make sure that the hose is not pinched or Do not operate your product at the same bend.
programme. protection are specified in the “Technical C If the dryer is mounted on the washing Specifications” section. machine by means of a bracket, use of the • The specified voltage must be equal to your water drain hose is recommended. The mains voltage.
Initial preparations for drying Things to be done for energy saving: A B C • Make sure that you operate the product at its full capacity but pay attention to not exceeding it. • Spin your laundry at the highest speed possible when washing them.
emit flammable or explosive vapor. A Consider the information in the • Do not dry items cleaned with industrial "Programme Selection Table". Always chemicals in the dryer. start the programme in accordance with • Do not dry your unwashed laundry in the the maximum load capacity.
Selecting a Program and Operating Your Machine Control panel 1. Filter cleaning warning light 6. Start/Pause/Cancel button Warning light turns on when the filter is full. Used to start, pause or cancel the 2. Program follow-up indicator programme. Used to follow-up the progress of the 7.
Preparing the machine laundry from creasing will be activated if you 1. Plug in your machine. do not take the laundry out after the program 2. Place the laundry in the machine. has come to an end. This program rotates 3.
Auxiliary function dryer has started. For example; Buzzer Cancel Models Equiped 1. Press and hold the “Start/Pause/Cancel” Your machine will send out an buzzer warning button for about 3 seconds to “Cancel” when the program comes to an end. If you the programme in order to select “Extra do not want to hear this buzzing, you need Dry”...
on the “Start/Pause/Cancel” and “Cancel audio Ending the program through canceling warning” buttons simultaneously for 3 seconds. A new programme can be selected and To start a new program after the program is started after “Programme cancel” is activated over or to interrupt the program, the childproof in order to change the drying programme.
Maintenance and cleaning Cover filter Condensed water is not drinkable! Lint and fibres released from the laundry to the Never take out the water tank when the programme is running! air during the drying cycle are collected in the Water tank may be located in two different “Cover Filter”.
Solution suggestions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water. Laundry come out wet at the end of drying. • Meshes of the filter may be clogged. Wash with water. •...
Page 19
DRYER BUILT UNDER KIT ASSEMBLY INSTRUCTIONS 1) Remove 3 screw ( A ) and Pull out the top plate. 2) Remove the 4 support bracket (If exist) ( B ) by unscrewing the screws shown in the figure. 3) Unscrew the 2 screws ( C ) located on the back top corners of the dryer and the 3 screws ( D ) which fixed front panel.
Need help?
Do you have a question about the APS62CS and is the answer not in the manual?
Questions and answers