Manual Operation - Lennox Hearth Products MONTAGE 32FS Quick Start Manual

2

MANUAL OPERATION*

Hopper lid must
be closed during
operation.
The control board is located on the left
side of the stove.
COMBUSTION
AIR
O
Combustion Air Trim
(-) (+)
Used to fine tune the amount of
combustion air to better accom-
HEAT
START
OUTPUT modate variables such as venting
configuration, altitude and fuel.
* Refer to the Manual if you are connecting your stove to a thermostat. Ignition and control board functions for
BLOWER
automatic (thermostat) operation are different from the explanations given above.
PELLET
FEED
3 O
(-) (+)
FEEDING
FLAME APPEARANCE
STOP
The appearance of the flame can be a good indicator of the overall performance of the stove. A bright clean flame
indicates proper balanced and efficient burning, while a dark slow-moving flame indicates incomplete combustion
HEARTH PRODUCTS
and a stove that may be in need of service and/or adjustment.
PROPERLY ADJUSTED FLAME
The stove burns clean and heats efficiently.
COMBUSTION
AIR
O
(-) (+)
HEAT START
OUTPUT
BLOWER
PELLET
FEED
O
(-)
FEEDING
STOP
HEARTH PRODUCTS
COMBUSTION
AIR
O
(-) (+)
Heat Output Button
HEAT
START
Once the stove is running, you
OUTPUT
can use the heat output button
to choose between five levels
ranging from low to high.
BLOWER
PELLET
FEED
O
(-) (+)
FEEDING
STOP
HEARTH PRODUCTS
• SHARP ACTIVE
FLAME
• BRIGHT YELLOW HUE
• PELLET EMBERS
ACTIVELY MOVE IN
THE ULTRAGRATE
STARTING THE MONTAGE™ PELLET STOVE
1. Fill the hopper with pellets
COMBUSTION
AIR
O
2. Make sure the hopper lid is completely closed
(-) (+)
3. Press the "START" button on the control panel to
begin the ignition cycle
HEAT START
OUTPUT
RE-FUELING WHILE IN OPERATION
1. Open hopper lid and fill hopper with pellets
COMBUSTION
AIR
BLOWER
O
2. Make sure the hopper lid is completely closed
(-) (+)
PELLET
FEED
O
3. Check to make sure the stove remains lit
(-) (+)
FEEDING
HEAT START
4. If the flame goes out, press the
OUTPUT
on the control panel to re-ignite
(+)
STOP
Failure to ensure that pellets in the UltraGrate™ remain burning
BLOWER
after re-fueling may result in smoke escaping from the unit.
PELLET
HEARTH PRODUCTS
FEED
O
(-) (+)
STOPPING THE MONTAGE PELLET STOVE
FEEDING
COMBUSTION
AIR
1. Press the O "STOP" button
(-) (+)
(The fans will automatically turn off once the stove
STOP
has cooled down)
HEAT START
OUTPUT
HEARTH PRODUCTS
Blower Button
BLOWER
The blower button is used to
PELLET
vary the output of the room fan.
FEED
O
Choose between five levels rang- (-) (+)
ing from low to high. FEEDING
STOP
HEARTH PRODUCTS
IMPROPERLY ADJUSTED FLAME
Requires more frequent maintenance and can be unsafe
to operate.
COMBUSTION
AIR
O
(-) (+)
"START" button
HEAT START
OUTPUT
BLOWER
PELLET
FEED
O
(-) (+)
FEEDING
STOP
COMBUSTION
AIR
O
Pellet Feed Trim
(-) (+)
HEARTH PRODUCTS
Used to fine tune the amount of
pellets fed into the UltraGrate™
HEAT
START
OUTPUT and accommodate variations in
pellet size.
BLOWER
PELLET
FEED
O
(-) (+)
FEEDING
STOP
HEARTH PRODUCTS
• SLOW LAZY FLAME
• DARK ORANGE HUE
• LARGE FLAME WITH
BLACK SOOTY TIPS
• PELLETS BUILD UP IN
THE ULTRAGRATE