Table of Contents
Advertisement
HAND FINISHING
ORBITAL SANDER
40070
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright
2002 by Harbor Freight Tools
. All rights reserved. No
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Manual Revised 10/05
Advertisement
Table of Contents
Related Manuals for Drill Master 40070
Summary of Contents for Drill Master 40070
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.
-
Page 2: Specifications
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. SKU 40070 For technical questions, please call 1-800-444-3353. ”... -
Page 3: Electrical Safety
Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. SKU 40070 For technical questions, please call 1-800-444-3353. ELECTRICAL SAFETY... -
Page 4: Tool Use And Care
Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SKU 40070 For technical questions, please call 1-800-444-3353. TOOL USE AND CARE... -
Page 5: Specific Safety Rules
Maintain labels and nameplates on the Sander. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. When using a handheld power tool, always maintain a firm grip on the tool with both hands to resist starting torque. -
Page 6: Grounded Tools: Tools With Three Prong Plugs
The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only SKU 40070 For technical questions, please call 1-800-444-3353. -
Page 7: Double Insulated Tools: Tools With Two Prong Plugs
Association, and the National Electrical Code. (See Figure B.) Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) SKU 40070 For technical questions, please call 1-800-444-3353. FIGURE B... -
Page 8: Extension Cords
Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. SKU 40070 For technical questions, please call 1-800-444-3353. EXTENSION CORDS (See... -
Page 9: Assembly Instructions
When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 12. -
Page 10: Attaching Sandpaper To Backing Pad
NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 12. CAUTION: Always make sure the Power Cord (17) of the Sander is unplugged from its electrical outlet prior to making any adjustments to the tool. -
Page 11: Parts List
INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch (3) of the Sander is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of the Sander. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. -
Page 12: Assembly Diagram
ASSEMBLY DIAGRAM Part 0 - Dust Collection Chute - not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individu- ally as replacement parts. SKU 40070 For technical questions, please call 1-800-444-3353. Page 12...