Page 1
2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.
Failure to follow all instructions listed in this manual may result in electric shock, fire, and/or serious injury. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. SKU 93853 For technical questions, please call 1-800-444-3353 PRODUCT SPECIFICATIONS Description 120 VAC / 60 Hz / 1500 Watts 20 AMPs (Start Up) / 9.5 AMPs (No Load) / 13.0 AMPs (With Load)
“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock. Stay alert. Watch what you are doing, and use common sense when SKU 93853 For technical questions, please call 1-800-444-3353 ELECTRICAL SAFETY...
Page 4
Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. Properly SKU 93853 For technical questions, please call 1-800-444-3353 TOOL USE AND CARE...
Maintain labels and nameplates on the Demolition Hammer. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Always wear ANSI-approved safety impact eye glasses and a full face shield when using the Demolition Hammer.
Page 6
The Chisel may become hot after prolonged use. When removing the Chisel from the tool, avoid contact with skin and use proper protective gloves when grasping the Chisel. SKU 93853 For technical questions, please call 1-800-444-3353 PAGE 6...
Page 7
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 93853 For technical questions, please call 1-800-444-3353 SAVE THESE INSTRUCTIONS...
The plug and outlet should look like those in the following illustration. (See Figure A.) THIS PRODUCT DOES NOT USE A 3-PRONG PLUG FIGURE A SKU 93853 For technical questions, please call 1-800-444-3353 GROUNDING WARNING! ELECTRICAL OUTLET 120 VOLT,...
When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure C.) SKU 93853 For technical questions, please call 1-800-444-3353 EXTENSION CORDS 120 VOLT,...
Page 10
12.1 – 16.0 16.1 – 20.0 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE D SKU 93853 For technical questions, please call 1-800-444-3353 (120 VOLT) EXTENSION CORD LENGTH Feet Feet...
When unpacking, check to make sure all the parts shown on the Parts List on page 16 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
Demolition Hammer. Also wear heavy duty steel-toe boots, hearing protection, dust mask or respirator, and heavy duty work gloves. SKU 93853 For technical questions, please call 1-800-444-3353 SLIDER (4) OIL OR GREASE...
If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. SKU 93853 For technical questions, please call 1-800-444-3353 PAGE 13...
Page 14
CAUTION! All maintenance, service, or repairs not mentioned in this manual must only be performed by a qualified service technician. BRUSH CAP BRUSH HOLDER COVER (79) FIGURE G SKU 93853 For technical questions, please call 1-800-444-3353 (77) BRUSH HOLDER CARBON BRUSH (76)
Tool does not run. Tool does not stop. Poor cutting efficiency. Tool overheats and suddenly stops running. SKU 93853 For technical questions, please call 1-800-444-3353 TROUBLESHOOTING Possible Solution 1. Make sure the Chisel shank, Front Cap, and Slider are free of debris and lightly oiled or greased.
---------- ----------------------------------------------- * Cannot be ordered individually. Must be ordered as a complete Motor Assembly. ** Cannot be ordered individually. Must be ordered as a complete Carbon Brush Assembly. SKU 93853 For technical questions, please call 1-800-444-3353 PARTS LIST Qty.
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the motor is free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all other par ts and components of the product are free from defects in materials and workmanship.