IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work.
Inlet PSI Average Air Consumption Paint Capacity Air Inlet Nozzle Size You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Page 4
Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.
When unpacking, check to make sure the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.
For best service you should incorporate a regulator and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. Note: Compressor pumps discharge condensed water, oil, or other contaminants along with the compressed air.
IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work.
IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work.
Page 9
IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work.
IMPORTANT: Before using for the first time, the spray gun must be cleaned using a solvent based thinner. If not removed, the red oil used by the manufacturer for testing and corrosion protection may contaminate paint. IMPORTANT: The Spray Gun must be cleaned immediately after use. Improper cleaning is a common reason for the Spray Gun not to work.
Always follow the paint manufacturer’s recommendations for cleaning, solvent type, and disposing of used solvent. Note: Due to the viscosity of latex and other water-based paints, they are not recom- mended for use with this or other HVLP (High Volume Low Pressure) sprayers. Oil Based Paints: Use mineral spirits.
Part description Handle Safety Valve Lock Nut Spring Valve Valve Gasket Valve Seat Connector Screw Fluid Flow Knob Spring Suction Tube Gasket Rivet Gasket Tube Screw Spring Rivet (Qty. 2) E-clip Air Regulator Lock Nut Air Adjusting Seat Spring Seat Air Adjusting Seat Spring Seat Air Adjusting Screw...
Assembly Diagram NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 01/07 For technical questions, please call 1-800-444-3353; SKU 93305 Page 13 Troubleshooting section at end of manual.
The Patterns below resemble symptoms of spray pattern problems. Please refer to the accompanying possible problems if you are experiencing similar difficulties. The solution to each problem follows the problem in parentheses. Problem 1: 1. The Pattern Control Knob (57) is partially closed. (Open Pattern Control Knob (57).) 2.
Page 15
Problem Sputtering Spray Will Not Spray Overspray Fluid Tip Leakage Air Leaking from Air Cap Fluid Leaking from Packing Nut 1. Packing Nut loose If the steps above do not solve the problem or if the repairs involved are too SKU 93305 For technical questions, please call 1-800-444-3353.
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of pur- chase.