Central Pneumatic 30224 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Paint Sprayer
  5. 30224
  6. Assembly and operating instructions manual

Central Pneumatic 30224 Assembly And Operating Instructions Manual

Paint spray gun
Hide thumbs Also See for 30224:
Table of Contents

Advertisement

Quick Links

PAINT SPRAY GUN
30224
ASSEMBLY AND OPERATING
INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright
1997, 2005 by Harbor Freight Tools
. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Manual Updated 09/05

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 30224 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Central Pneumatic 30224

Summary of Contents for Central Pneumatic 30224

  • Page 1 © ® Copyright 1997, 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

  • Page 2: Table Of Contents

    Troubleshooting ... 14 When unpacking, check to make sure the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

  • Page 3: Specifications

    Use eye and ear protection. Always wear ANSI approved impact safety goggles. Always wear an ANSI approved dust mask or respirator when using this Spray Gun. For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Specifications 30-80 PSI, 80 PSI Max.
  • Page 4 Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.
  • Page 5 For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Page 5...

  • Page 6: Air Connection

    For best service you should incorporate a regulator and inline filter, as shown in the diagram above. Hoses, couplers, regulators, and filters are all available at Harbor Freight Tools. Note: Compressor pumps discharge condensed water, oil, or other contaminants along with the compressed air.

  • Page 7: A Comparison: Conventional Versus Hvlp Spray Guns

    If it appears to thin, add a very small amount of thinner (not included). BE CAREFUL when thinning. Proceed slowly, adding very minimal amounts. NEVER exceed the manufacturer’s thinning recommendations. For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Conventional HVLP...

  • Page 8: Fan Direction And Pattern Adjustment

    FIGURE 1 on page 6). By turning it counterclockwise (all the way open), the pattern will flatten. Turn the Pattern Control Knob (13) clockwise for a round pattern. See FIGURE 4 below. Flat/Open For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Horizontal Fan Air Cap Vertical Fan...
  • Page 9 (you see globs of paint), close down the Fluid Control Knob (29) slowly, checking the mixture after each adjustment. See FIGURE 5 below. Too Coarse (Tighten) For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. FIGURE 5 Correct Too Fine (Loosen)

  • Page 10: Techniques

    Clean out the gun thoroughly after EVERY use, according to the instructions found on the next page. For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Techniques FIGURE 6...

  • Page 11: Maintenance

    Disposal: After cleaning your Spray Gun, properly dispose of your cleaning solutions according to the solution manufacturer’s direction and local hazardous waste standards. For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Maintenance SOLVENT SELECTION and disposing of used solvent.

  • Page 12: Parts List

    THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Parts List t s i...

  • Page 13: Assembly Diagram

    Assembly Diagram For technical questions, please call 1-800-444-3353; SKU 30224 Page 13 Troubleshooting section at end of manual.

  • Page 14: Troubleshooting

    2. Holes on one side of the Air cap are plugged. (Clean the Air cap with a nonmetallic point.) If the steps above do not solve the problem or if the repairs involved are too SKU 30224 For technical questions, please call 1-800-444-3353.
  • Page 15 5. Bent valve stem Fluid Leaking from 1. Packing Nut loose Packing Nut 2. Packing worn or dry For technical questions, please call 1-800-444-3353; SKU 30224 Troubleshooting section at end of manual. Solution 1. Refill 2. Hold upright 3. Clean vent hole 4.

Table of Contents

Save PDF