Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nilfisk-ALTO MD 8000
Summary of Contents for Nilfisk-ALTO MD 8000
- Page 2 English...
-
Page 3: Table Of Contents
English Contents Components Symbols used to mark instructions..........4 Attachments Included Attachments..............5 & 6 Guidance Congratulations................7 Getting the best results...............7 Installation Assembly..................8 Warnings..................8 Operation Switching on the machine............9 Using the machine..............9 & 10 During Use..................10 Maintenance Daily....................11 Weekly..................11 Precautions Do’s & Don’ts................11 Service Guarantee...................12 Technical... -
Page 4: Components Symbols Used To Mark Instructions
English Components Diagram A 1. Collection Tank 2. Vacuum Hose Socket 3. Steam Hose Socket 4. Castor with Brake 5. Caster with No Brake 6. Serial Number 7. Cold Water Tank 8. Wire Basket 9. Tubular Handle 10. Chemical Connector 11. -
Page 5: Attachments Included Attachments
English Attachments These Parts were carefully packed at Nilfisk ALTO. Please check all accessories on receipt. If any parts are missing or damaged please contact the company in which you purchased this machine, within 7 days of purchase quoting your serial number on the back of the machine. - Page 6 English Attachments cont.. 13. Suction Nozzle 150mm 14. Clip on Squeegee 150mm 15. Clip On Brush 150mm 16. Accessory Service Kit 17. Steam, Vacuum Nozzle (Small) 18. Short Steam Lance (Plastic) 19. 95mm Triangular Brush 20. Crevice Tool 21. Ice Scraper Diagram D •...
-
Page 7: Guidance Congratulations
Guidance Congratulations ………………………………………………... We would like to take this opportunity to thank you for your purchase of the Nilfisk ALTO combined steam, detergent and vacuum cleaner. The MD8000 is manufactured in the EU to the highest quality Standards This instruction manual contains all of the necessary information to operate and maintain this machine. -
Page 8: Installation Assembly
English Installation • Place Tubular Handle (Diagram D) in position on the back of the machine and secure using the 4 x Plastic Wing Nuts (Diagram D). Do not screw them all the way in at this point. • Place Wire Basket (Diagram D) over the Wing Nuts and tighten up to secure. •... -
Page 9: Operation Switching On The Machine
6. Plug the power cable into a 240 Volt supply. Inspect the electric cable before every use. If the cable becomes damaged at anytime the complete cable must be replaced by a Nilfisk ALTO approved distributor. Never touch the power cable or plug with wet hands Always unplug the machine when i. -
Page 10: During Use
English Operating Procedure cont…. ………………………………………………... 11. The handle controls are now active. • The red trigger on the hose handle will release steam when pressed. • The red button on the side of the handle will lock the steam trigger in the off position. -
Page 11: Maintenance Daily
English Maintenance Warning: Disconnect the machine from the mains before cleaning or carrying out any maintenance work. Daily Maintenance ………………………………………………... To be carried out every day or every 8 hours of operation. 1. Grease “O” rings on the steam pin in the steam hose. 2. -
Page 12: Service Guarantee
Guarantee ………………………………………………... Nilfisk ALTO guarantees that if within 12 months from the date of purchase this appliance, or any parts thereof, is proved to be defective by reason of faulty workmanship or materials, we will at our option repair or replace the same free of charge for labour and materials, provided that: •... -
Page 13: Technical Technical Data
English Technical Technical Information ………………………………………………... Boiler Wattage: 3000W – (2000 +1000) Type: Stainless Steel Capacity: 3.3 Litres Continuous Fill Steam Pressure 8 Bar 165°C > Steam at source: Vacuum Type Integral Motor 850 Watt Electrical Voltage 230V ~ single phase Low Voltage Controls Cord length Capacities... -
Page 14: Troubleshooting Symptom, Possible Cause & Action
English Trouble Shooting Symptom Possible cause Action No power Not connected / Faulty socket Check connection to wall socket and socket switch. Try in another wall socket On / Off switch not on Press On / Off switch which will illuminate when on Fuse blown Replace fuse with approved 13A fuse... - Page 15 ...
- Page 16 ...
Need help?
Do you have a question about the MD 8000 and is the answer not in the manual?
Questions and answers