Advertisement
®
FRAMING NAILER
21 DEGREE ANGLED / 10 GAUGE
Model 04041
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright
2004 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Revised Manual 01/04, 05/04, 09/04
Advertisement
Table of Contents
Related Manuals for Central Pneumatic 4041
Summary of Contents for Central Pneumatic 4041
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. Revised Manual 01/04, 05/04, 09/04...
-
Page 2: Product Specifications
Wear restrictive hair covering to contain long hair. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. SKU 04041 For Technical Questions, Please Call 1-800-444-3353 PRODUCT SPECIFICATIONS (.113”... - Page 3 Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs.
- Page 4 26. Stay within air pressure capacity. Never operate the Nailer above 120 PSI. 27. Hold tool away from head and body. During operation the Nailer may kick back causing injury. SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 4...
-
Page 5: Operation
When unpacking, check to make sure all the parts shown on the Parts List on page 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. -
Page 6: Loading Nails
Bracket B (part #35), or Safety (part #38) depressed. (See Figure B) Pull the Feeder Shoe (part #52) all the way to the rear, until it latches. (See Figure B.) SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Loading Nails... - Page 7 With the nose of the Nailer on the workpiece, squeeze the Trigger again to fire another nail. Continue firing nails as needed. When the work is completed, disconnect the air supply and remove the nails from the nailer. SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Loading Nails (continued) OPERATION...
- Page 8 (See Figure C). Test fire a nail, and check its depth of drive. Repeat Step #2 as necessary to achieve the desired depth of drive. (See Figure C). SKU 04041 For Technical Questions, Please Call 1-800-444-3353 EXHAUST COVER (#4) QUICK COUPLER &...
-
Page 9: Clearing Jams
Feeder Shoe (#52) back into position. If you are unable to clear the nail jam using the method prescribed above, the tool should be taken to a qualified service technician for proper servicing. SKU 04041 For Technical Questions, Please Call 1-800-444-3353 RUBBER COVER (39) -
Page 10: Inspection, Maintenance, And Cleaning
When necessary, wipe with a damp cloth, using a mild detergent or mild solvent. When storing, keep the Framing Nailer in its Carrying Case (part #80) or covered with a clean cloth. SKU 04041 For Technical Questions, Please Call 1-800-444-3353 FIGURE D Probe in these areas with a screwdriver to release jammed nails. - Page 11 SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 11...
- Page 12 BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 12...
Need help?
Do you have a question about the 4041 and is the answer not in the manual?
Questions and answers