Advertisement
Quick Links
Installation
Instructions
CHANDLER™ APRON KITCHEN SINK
MODEL 7048 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
BEFORE YOU BEGIN...Unpack new sink and inspect carefully for damage. Replace the sink in its original
packing carton to protect it until you are ready to begin installation.
RECOMMENDED TOOLS & MATERIALS
Putty Knife
Pipe Wrench
Channel Locks
Drill
PRODUCT REQUIREMENTS
Due to the special nature of this installation, American Standard recommends that an experienced cabinet
maker build the new cabinet or modify an existing cabinet to achieve a satisfactory installation.
To ensure proper fit of the sink in the cabinet, we suggest you provide the cabinet maker with the actual sink
that will be installed.
NOTES
The cabinet designs illustrated below are intended as suggestions only. Your specific installation requirements
may vary from those shown.
CABINET DESIGN
The sink is designed to be installed with the apron exposed and the back of the apron flush against the front of
the cabinet.
SINK DIMENSIONS
7-1/8
(181mm)
8-3/4
(222mm)
22
(558mm)
6-3/16
(157mm)
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.
®
Corian
Dupont registered trademark
™
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Basin Wrench
1-3/8 (35mm) DIA.
HOLES TYP.
C/L
1 (25mm)
RAD. TYP.
4-1/2
9-1/2
(114mm)
(241mm)
36
(914mm)
24-1/2
(622mm)
TILE RECESS
33 (838mm)
M
A D E
W I T H
Saber Saw
Plumbers' Putty or
Caulking
Various Carpentry Tools
1-3/4
(44mm) DIA.
7048.804
4 HOLE
VARIATION
3-1/2
(89mm) DIA.
1-1/2
(38mm) REF.
SEALING
COMPOUND
3/8
(10mm)
9-3/4
(248mm)
FRONT OF
CABINET
Certified to comply with ANSI Z124.6
Patent Pending
Observe local plumbing and building codes.
7 9 0 7 5 9 - 1 0 0 R E V A
Tubing Cutter
Tape Measure
Hacksaw
Silicone Adhesive
NOTE: Tile recess is
designed to accept four
6" x 6" x 5/16" thick tiles
(by others). Secure tiles
with silicone adhesive.
2
(51mm)
© American Standard Inc. 2004
Advertisement
Related Manuals for American Standard Chandler 7048 Series
Summary of Contents for American Standard Chandler 7048 Series
-
Page 1: Installation Instructions
Basin Wrench PRODUCT REQUIREMENTS Due to the special nature of this installation, American Standard recommends that an experienced cabinet maker build the new cabinet or modify an existing cabinet to achieve a satisfactory installation. To ensure proper fit of the sink in the cabinet, we suggest you provide the cabinet maker with the actual sink that will be installed. - Page 2 SINK INSTALLATION Mark COUNTERTOP SHOULD BE MAXIMUM 25mm (1") CABINET FACE A. Mark center of backside of sink. Mark center of location on counter top approx. 22in. from outside edge of countertop. B. Mark countertop to show the cabinet face location (dim. X) . C.
- Page 3 COUNTERTOP NOTCH AND CABINET CUTOUT SINK CUTOUT LINE FOLLOW THE SINK CUTOUT LINE VERTICALLY DOWN ON THE CABINET 9-1/4 (235mm) 32-1/4 (819mm) CABINET FACE CUTOUT A. The cut allows the apron portion of the sink to fit in the countertop. B.
- Page 4 CORIAN SINK If inspection of the Corian Sink of this American Standard product, within ten years after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.