Connecting With Rf Cable - Panasonic NV-VP33EB Quick Start Manual

Connecting with RF cable

You can connect the VCR to your TV
set by using a RF cable.
AC IN~
C O
DV O D UT
L
A UDI O
R
4
AC mains lead
1
AC mains socket
4
VCR Display
Auto Setup
Tuning : Ch 21
EXIT
: exit
Owner ID
PIN number : ****
Name : **************
House No : ***********
Postcode : ***********
You now have the opportunity
to enter your details and
help the police crack crime
see instruction book.
ENTER
: select : store
MENU : return EXIT :
exit
Datum / Zeit Clock set
MANUAL
Time : 12 : 00 : 00
Date : 11. 6. 05
RF IN
Aerial input
VCR/DVD
R IN F
V S
D D V / H
O T U
C O M M O N A 1 V
M O E T N N V D I E O O U T V DE I O
P (T ) V
R S E S V I E /
(P O R G
T R A E E L C )
N I
Y
P B L
R O T U
F
V A 2
(E X T)
A UDI O
R
C O A X I L A
P R
D I I G T A A L UD I O O UT
RF OUT
Aerial output
3
RF coaxial cable
TV
Aerial input
AC mains lead
VCR Auto Setup with RF cable
Turn on your television set.
With the Stand-by/on switch turn on the VCR/DVD. Automatic tuning
for all available TV stations begins. Approximate duration is 5 minutes.
After Automatic tuning has finished, press EXIT. The Owner ID screen will
appear.
- While Auto Setup is running the first digit of the VCR display will flash.
After a while it will stop flashing and the RF output channel number will
be displayed.
- Select an unused channel pre-set on your TV and tune it to the RF
output channel number shown on the VCR display (or until you can
clearly see the Auto Setup screen). Store the new video playback
channel (refer to the instructions for your TV).
In some cases, the RF output channel may interfere with the TV
stations transmitted in your area. This may prevent you from seeing the
On-Screen Display clearly. Please see page 5 for removing the
interference before restarting Auto Setup (page 35 of Operating
Instructions).
Owner ID
You can complete the Owner ID now or skip this step and do it later. To
do it later, press the EXIT button. Your VCR is now ready to use.
Optionally, you can have a QUICK SETUP following VCR Auto Setup for
the DVD player (page 6).
To set the Owner ID now, press the Numeric buttons or
a four-digit PIN number.
Press , to correct the digit.
Make sure that you will remember the PIN number (make a note of it).
Press the ENTER button twice to confirm.
Enter the [Name], [House No] and [Postcode] in the same way.
Press the ENTER button to confirm each entry.
Press the EXIT button to leave the Owner ID screen.
You will now see the TV picture. Your VCR is now ready to use. Optionally,
you can have a QUICK SETUP following VCR Auto Setup for the DVD
player (page 6).
If the clock setting menu appears
(Auto clock set was not possible due to a weak signal)
Press
Press the ENTER button to finish this setting.
Mind that a wrong date or time will influence the programmed
recording of TV programmes (don't forget to change summer
time and winter time).
- 2 -
2
Aerial
Follow the steps described below.
1
Ensure TV Power is disconnected
from AC Mains socket.
2
Connect aerial to the RF IN (Aerial
input) connector of the VCR/DVD.
3
Connect the VCR/DVD´s RF OUT
(Aerial output) to the TV set's
Aerial in connector.
4
Connect VCR and TV set to the
AC mains socket.
Follow the steps for VCR Auto Setup.
(Automatic tuning)
to set the correct time and date.
to enter