Time Stamp Function; Vhs Index Search System - Panasonic NV-HV62GH Operating Instructions Manual

Confirming the cassette which includes a
programme you want to watch
(Jet Navigator Memory)
This allows you to search the cassette which you recorded the
programme you want to watch without inserting video
cassette tapes.
Preparations
• Display the VCR picture on the TV.
• You can only search for cassettes recorded in timer
recording with setting [JET NAVIGATOR] to [ON]
(See page 8) on this VCR in the past.
1 Press [MENU] (9) to display the Main menu on the TV
screen.
2 Press [43] (28) to select [NAVI MEMORY 1
then press [ENTER] (26).
• NAVI MEMORY Screen appears.
• The programme list for 1 cassette
is displayed per 1 screen.
• Up to 20 cassettes can be
selected on this VCR and
displayed on the NAVI MEMORY
Screen.
* The number of Jet Navigator Data memorized on this
VCR is displayed.
3 Press [2 1] (28).
• The display can be switched for each cassette
(programme list).
To Cancel the NAVI MEMORY Screen:
Press [MENU] (9).
To Demonstrate the Jet Navigator Function
Keep [NAVI] (25) pressed for more
than 5 seconds without inserting a
cassette tape.
To Cancel the Demonstration of Jet Navigator Function:
Press [MENU] (9).
To Check the Recorded Programming Data

(Time Stamp Function)

When playback starts after searching
with Jet Navigator function or index
search function, recorded programming
data (called Time Stamp) appears on
the TV screen for approx. 5 seconds.
Note:
• Time Stamp does not appear if the beginning of the Jet
Navigator data is not recorded 10 minutes before and after
the current tape position even when index signals are
recorded.
To Find the Beginning of Each Recording

(VHS Index Search System)

This VCR automatically records special index signals on the
tape every time a recording is started. The Index search
function makes use of these index signals to let you find the
beginning of a desired programme quickly and easily.
16
LSQT0876
Index signals are automatically recorded in the following
cases:
• When you start a recording by pressing [REC] (15) or [REC/
OTR] (39).
• When a timer recording starts.
• When you press [REC] (15) on the remote control during
recording.
Conditions for correct operation of the Index search
function:
• The VCR must be in the stop mode or in the playback mode.
• Each programme recorded on the tape must be at least
5 minutes long.
Preparations
• Display the VCR picture on the TV.
*
• Insert a recorded video cassette.
PROG.]
Operation
1 Press [INDEX] (13) (that corresponds to the direction
NO.01 NAVI MEMORY
DATE CH ON CATEGORY
10/18 1 10:30 MUSIC
SELECT : END : MENU
To Cancel the Index Search or to Stop Playback:
NO.01 JET NAVIGATOR
DATE CH ON CATEGORY
Press [STOP] (12).
1/10 2 8:00 MUSIC
1/10 6 19:00 SPORT
1/10 4 21:00 MOVIE
1/10 6 22:00 CHILD
Notes:
• Searching in either direction is possible up to the 20th index
DEMONSTRATION
signal.
SELECT : NAVI END : MENU
• If you press either of [INDEX] (13) too many times, simply
press the other [INDEX] (13) (indicating the opposite
direction) to correct it. In this way, you can reduce the
displayed figure down to 1.
• The figure on the VCR display decreases by 1 every time an
index signal is located.
Finding a Timer-recorded programme for
CH 2 10/29. SA ON 20:02
viewing (Easy Programme Playback)
Allows you to find a timer-recorded programme with
One-touch operation and to play it back easily.
Preparation
Set timer recording for the programme you wish to view.
Operation
1 Press [PROG PLAY] (21).
To Cancel the Easy Programme Playback:
Press [STOP] (12).
Notes:
• The VCR memorises the position at which timer recording is
set to the standby mode by pressing [TIMER (REC)] (14) as
the start point of Easy Programme Playback.
• If you take out the cassette after a timer recording has
finished, Easy Programme Playback function does not work.
from the current tape position in which the desired
programme is located on the tape) to start the index
search.
For example, if you want to search for the 2nd
recorded programme in forward direction, press
[INDEX] (13) (L) twice.
• The VCR fast-forwards or rewinds the tape and searches
for the specified index signal (the beginning of the desired
recorded programme).
When it is found, playback starts automatically.
• As soon as the timer-recorded
programme is found, playback
starts automatically.
2222
PROG PLAY