Siemens WLM20460BY Installation Instructions Manual

Safety instructions
– The washing machine is heavy - take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not install the washing machine outdoors or in
areas where there is a risk of frost.
– The washing machine may be damaged. Do not lift by projecting components (e.g. washing
machine door).
– In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
– If in doubt, have the appliance connected by a technician.
– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmental disposal
– Dispose of packaging in an environmentally friendly manner.
– This appliance has been identified in accordance with the European Directive 2002/96/
EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive specifies a
framework for the return and recycling of waste appliances and is valid throughout Europe.
Humidity in the drum is
Scope of delivery
according to model
caused by the final inspection.
Aqua-Stop Aqua-Secure Standard
Covers Elbow
Hose holder
for fixing the waste
water hose
Depending on the connection
– A 24-40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers) page 4: Water connection.
Useful tool
– Spirit level for aligning the washing machine.
Installation area
– Stability is important to prevent the machine from wandering.
– The installation area must be firm and level.
– Soft floors/floor coverings such as e.g. carpets are not suitable.
If installing the appliance on a wooden joist floor
– If possible, install the washing machine in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is essential to secure the washing machine feet with holding brackets*.
*order no. WMZ 2200, WX 9756
Hose and cable lengths
depending on model
Connection on left side or
~ 135 cm
Water drainage
~ 95 cm
Power cord
~ 160 cm
Water supply
Note
: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
– Aqua-Stop extension hose**, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard model.
**order no. WMZ 2380, WZ 10130
Built-under/Built-in appliance
Build-under/build-in before connection to the power supply.
Installed in between kitchen units (built-under or built-in)
– 60 cm cavity width required.
– Install washing machine only under a continuous worktop that is connected firmly to the
adjacent cupboards.
1
Removing transport bolts
– Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
– If transporting the appliance subsequently, always re-install the
transport bolts - this prevents damage to the machine
– Retain the screw and spacer.
1. Take the hoses (depending on the model) out of the holder and the elbow.
Remove the elbow.
Connection on right side
2. Undo and remove all 4 transport bolts.
~ 100 cm
3. Take the power cord out of the holders. Remove the sleeves.
~ 140 cm
~ 165 cm
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
The hose holder in this position is
longer than the others. Please
ensure that the right part is used.
5. Fix the hoses in the hose holders.
2
Water connection
– Risk of electric shock! Do not immerse the Aqua-Stop safety device in water (contains an
electric valve).
– To prevent leakage or water damage, follow the instructions in this chapter.
– Attention: operate the washing machine with cold drinking water only.
page 6.
Do not connect to the mixer tap of a pressureless hot-water heater.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
– If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
– Attention: do not kink, crush, modify or cut through
(strength is no longer guaranteed).
Optimum water pressure in the mains: 100-1000 kPa (1-10 bar)
– When the tap is turned on, the water flow is at least 8 l/min.
– If the water pressure is higher, install a pressure reducing valve.
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the connection
points are not leaking.
Attention: the screw connection is under water mains
pressure.
Water drainage
Water drainage hose:
Attention: do not kink or stretch.
Height difference between installation area and outlet:
0- 100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out of
the sink.
Attention: the plug must not be in the plug hole. When the water is being
pumped out of the washing machine, check that the water drains away
quickly enough. Do not immerse the end of the drainage hose in the water
that has been pumped out. There is a risk that water will be drawn back
into the washing machine.
Drainage into a siphon:
Attention: secure the connection with a 24-40 mm dia. hose clip
(available from a specialist retailer).
.
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slipping out of
the drain.
3
depending on model
Model: Aqua-Stop Standard
Aqua-Secure
3/4 ''
min 10 mm
max. max.
90° 90°
3/4 ''
min 10 mm
4