Advertisement
9
Setting your security code
a
In an effort to fight crime, we have equipped your TV
with security protection. When activated your TV is
protected against unauthorised use. You cannot
operate the unit if you forget the PIN code. Please
ensure that you keep a record of the PIN code in a
safe place, in case you forget it.
If the unit needs to be serviced, make sure that the
security protect function is OFF, otherwise you will be
charged for resetting this feature.
If you enter the wrong PIN code more than 3 times, the
Press MENU on the remote control.
unit will be locked and you will not be able to operate
The main control menu will appear.
your TV. To unlock the unit you must disconnect the
mains supply and wait for more than 30 minutes.
Press PROG/PAGE
Reconnecting the mains supply after this time will allow
registration menu.
you to enter the PIN code again.
Press ENTER to display the pin code registration screen.
Press PROG/PAGE
Then press ENTER. Press VOL +/- until the desired
letter is displayed.
Store the letter by pressing ENTER.
You can enter up to 20 letters.
Press MENU to register your name.
10
Manual Tuning
a
In certain areas with poor reception, the Automatic
Select the TV channel you want to manually tune.
Tuning System may not tune your television to the
strongest broadcast signal. If you are not satisfied with
Press MENU on your remote control. The main control
the automatic tuning you may manually tune your
menu will appear.
television to obtain the best possible picture and sound.
Press PROG/PAGE
highlight CH tuning (indicated by a flashing green
square).
Press ENTER on your remote control to confirm.
The CH tuning on screen display will appear.
Press PROG/PAGE
Press ENTER to confirm.
b
Press PROG/PAGE
/
Then press ENTER.
/
to select the pin code
Press numbered buttons on the remote control to enter
the PIN code (4 digits).
Your PIN code can be a combination of any 4 numbers.
/
to select owner's name.
Press ENTER to register the PIN code.
Press PROG/PAGE
/
menu.
Then press ENTER to select ON. Press MENU to return
to the main menu.
The security protect function will now be activated.
b
Press VOL + to search up the waveband or VOL – to
search down the waveband.
Each time a station is found the search will stop.
Press VOL + or – to continue searching until the station
/
on your remote control to
you want is found.
Press ENTER to store the station you selected.
Press PROG/PAGE
/
channel number (1~80).
Press ENTER to store the channel number.
/
to highlight manual.
Repeat this process to tune in other channels.
Press MENU three times to remove the tuning menu.
c
To cancel the security protect function select "protect
to select PIN code.
OFF" from the PIN CODE REGISTRATION menu.
If you turn off the MAIN POWER switch on the front of
the unit or the unit is unplugged from the mains supply
for more than 30 minutes, the PIN code screen will
appear on the screen when you next turn on the unit.
Enter your PIN code using the numbered buttons on the
remote control.
If you enter the correct PIN code, "PIN CODE OK" will
to select the protect on off
be displayed on the screen and you will be able to
operate the unit.
If you enter the wrong PIN code, "PIN CODE ERROR"
will be displayed on the screen, and you can try again.
c
If at a later date you wish to skip an unwanted channel
when using PROG/PAGE
/
remote control.
The channel number will flash when skip is selected for
that channel.
To cancel the skip function, type in the channel number
i.e. 2 and press SKIP.
to select your required
The channel number will stop flashing.
Fault finding guide
CAUSE
SYMPTOM
No standby light.
Is your TV plugged in ?
Is the main power switch on the
front of your TV off?
Has the fuse in the mains plug
blown?
No picture, no sound.
Is your TV plugged in ?
Is the aerial connection lead
broken or damaged?
Possibly station trouble.
Is the main power switch on the
front of your TV off?
Have you pressed Mute or have
you set the volume at minimum.
Unable to select channel
During automatic tuning your
numbers up to 80.
television didn't find enough
channels to place in these
numbered positions?
Poor or no colour.
Aerial or connection lead is not
connected or lead is damaged or
broken.
Colour control is not adjusted.
Remote control does not
Weak or exhausted batteries.
work or operates
erratically.
Unable to playback video
During automatic tuning your
tapes.
television you didn't have your
VCR switched on, therefore your
television was unable to find it.
Unable to watch Satellite
During automatic tuning your
stations.
television didn't find the Satellite
system.
Wiring Instructions & Specification
Warning: If the mains plug is cut from the mains lead of this appliance the plug must be destroyed. A mains
plug with bared wires is hazardous if engaged in a mains output socket.
The wires in your TV mains lead are coloured in accordance with the following:
• •
The wire which is coloured Blue must be connected to the terminal in the plug marked 'N'.
• •
• •
• •
The wire which is coloured Brown must be connected to the terminal in the plug marked 'L'.
• •
• •
No connection must be made to the earth terminal of the plug.
, press SKIP on the
• •
• •
You must use a 13 amp plug (BS 1363), and fit a 5 amp fuse (BS 1362).
• •
If any other type of plug is used a 5 amp fuse must be fitted, either in the plug, adaptor or at the
• •
distribution board.
Picture tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14" (32 cm visible) measured diagonally
Colour system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PAL I
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Loop aerial or 75 Ohm external aerial
Scart socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 x 21 pin
Audio output power . . . . . . . . . . . . . . . . . . . . . . . . . .1.5W
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3"(8 cm) 8Ohms
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AC 230-240 50Hz
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . .44W (10W in standby)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.5Kg
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .362(W) x 360(D) x 320(H)mm
SOLUTION
Plug your TV into mains socket
(AC outlet).
Press the main power switch.
Replace fuse in mains plug.
Plug your TV into mains socket
(AC outlet).
Check all aerial connections for
broken or damaged wires. If
necessary replace with new leads.
Move the aerial away from
possible source of interference. If
you live in a known poor
reception area try using an aerial
booster to improve the quality of
broadcast signal.
Press the main power switch.
Press Mute again or increase the
volume using the volume control.
If a television station has been
missed try repeating the automatic
tuning.
Check all aerial connections for
broken or damaged wires. If
necessary replace with new leads.
Try using an aerial booster to
improve the quality of broadcast
signal.
Adjust colour.
Replace batteries.
Before starting the automatic
tuning operation make sure you
have your VCR switched on and a
tape playing.
Before starting the automatic
tuning operation make sure you
have your Satellite system
switched on and Sky News
selected.
3J20101A V '00.07
Advertisement
