Messages; On The Unit's Display - Panasonic Diga DMR-EX769EB Operating Instructions Manual

Messages

On the Unit's Display

H , F
(" " stands for a service number.)
DVD
(" " stands for a number.)
GUIDE
HARD ERR

NoERAS
NoREAD
NoWRIT
FINAL
PLEASE WAIT

PROG FULL

SP 35:50, LP 151h
"SP", "LP" and the numbers are
examples.
SW-DL
UNSUPPORT

UNFORMAT

EXT-L
F74
F75
U59
U61
U76
U80, U81, U99
The message are alternately displayed.

 An error has occurred. The number following "H" or "F" depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
( 75, "To restore the unit if it freezes").
 If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
 The remote control and the main unit are using different codes. Change the
code on the remote control.
 GUIDE Plus+ data is being downloaded.
 If there is no change after turning the unit on and off, consult the dealer
where the unit was purchased.
 You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
 The disc is dirty or badly scratched. The unit cannot record, play, or edit.
 The disc may be incompatible or of poor quality.
 You have used a lens cleaner and it has finished operation. Press
[ OPEN/CLOSE] on the main unit to eject the disc.
 You cannot write to this disc.
The disc may be damaged. Use a new disc.
 When the screen asking if you want to finalise the disc appears, the
message is displayed.
 Displayed when the unit is started. This is not a malfunction.
 The unit is carrying out its recovery process. You cannot operate the unit
while the message is displayed.
 There are already 32 timer recording programmes. Delete unnecessary
timer recording programmes.
 Available space on the HDD or disc.
The example "SP 35:50" is displayed when less than 100 hours are
available and the example "LP 151h" is displayed when over 100 hours are
available.
"SP" and "LP" are recording modes, "35:50" means "35 hours 50 minutes"
and "151h" means "151 hours".
 The unit is performing a software update.
 You have inserted a disc the unit cannot play or record onto.
 You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R,
+R DL or DVD-RW (DVD-Video format) that has been recorded on other
equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
 This unit is in EXT LINK standby. EXT LINK has been turned on and will
stop operation on the unit until the recording has completed.
Press [EXT LINK] to stop recording or cancel linked timer.
 The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
 The HDMI connection could not be authenticated due to an internal data
malfunction. Consult the dealer where the unit was purchased.
 The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes
until the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.
 (When a disc is not inserted) Displays when a malfunction has occurred.
This is displayed when the unit is in the recovery process to return to
normal operation; it is not broken. Once the display disappears you can
use the unit again.
 HDMI cannot be output because you are connected to a model that does
not support copyright protection.
 The unit fails to operate properly. Press [/I] on the main unit to switch the
unit to standby mode. Press [/I] on the main unit again to turn the unit on.
Page
−
−
75
66
−
−
17
15, 16
7
−
25
−
−
29
−
66
15, 16
25
27
−
−
−
−
−
−
(Continued on the next page)
73
RQT9307