Connection To Other Equipment - Panasonic SL-CT720 Operating Instructions Manual

Using the Remote Control
Play desired tracks only (Program play)
While stopped, use [:] or [9] to select the track,
then press [ $ MEMO/ % DISP].
Track number Sequence number
3 01
M
will appear after
[ $ MEMO/ % DISP] is
pressed
Repeat to program up to 20 tracks.
Play
1/∫
Confirm $ MEMO
Cancel
1/∫
Changing the anti-skip mode
The anti-skip function (ANTI-SKIP SYSTEM) reduces or eliminates
skipping caused by vibration. You can change the anti-skip memory time.
While stopped, each time you press and hold [ $ MEMO/ % DISP]
POS 1
Anti-skip enhanced mode,
180-second anti-skip memory
You cannot change the memory time for MP3. It is a maximum of
≥
400 seconds for MP3 recorded at 128 kbps.

Connection to other equipment

Turn off this unit and the other equipment before connection.
Insert each plug fully.
Adjust the volume on the connected equipment.
If you don't want the remote control operation tone, turn it off (
Main unit
For Europe, Australia and N.Z.)
(
∫To remote control jack
Audio cable (
Set the unit's volume to 10-15.
Remote
control
(For areas except Europe, Australia and N.Z.)
∫To Optical digital/line out jack
(OPT OUT/OUT)
Digital connection
Optical cable (
Analogue connection
Audio cable (
No sound is output if MP3 is played using a digital connection. Use the
§
AC adaptor (included) when recording. (Using batteries only may
cause recording not to take place correctly.)
$ MEMO/ % DISP
MP3
01
Sequence number
3 1
ALBUM
Track number
Album number
Press after all desired tracks
have been programmed.
/
% DISP
Press during play.
Press during play.
("M"disappears.)
CD-DA
POS 2
Sound enhanced mode,
45-second anti-skip memory
➪
)
not included
To CD or AUX terminals
§
)
not included
To Optical jack
)
not included
To CD or AUX terminals
button
Changing the display
Each time you press and hold [ $ MEMO/ % DISP] during
play
Album
M
title
M
≥" ~ " is displayed in place of anything over 32 characters.
≥"_" is displayed in place of characters this unit cannot
display.
" appears instead if ID3 tags haven't been entered.
≥"
Enjoying more natural sound (Digital Re-master)
MP3
You can regenerate signal frequency lost during compression,
restoring the sound to near pre-compression form.
While stopped, each time you press and hold
[ $ MEMO/ % DISP]
Sound enhanced
Note on CD-R and CD-RW
(CD-DA/MP3 only)
For CD-DA format, use a music disc and finalize
unit may not be able to play some discs due to the condition of the
page 5).
recording.
§A process performed after recording that enables CD-R/CD-RW players to play
audio CD-R and CD-RW.
Playing MP3
MP3: One method of compressing data with little loss to the original sound
quality. MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.
∫When creating MP3 files to play on this unit
Disc formats: ISO9660 level 1 and level 2 (except for extended formats)
CD-ROM drive
001album
1
001track. mp3
002track. mp3
003track. MP3
002album
Audio
2
004track.mp3
005track.mp3
system
004album
and so
on
003album
4
006track.mp3
007track.MP3
∫Unit limitations
≥Only the artist name and track title ID3 tags (version 1.0 and 1.1) are displayed.
≥This unit is compatible with multi-session discs but if there are a lot of sessions it takes
more time for play to start. Keep the number of sessions to a minimum to avoid this.
≥This unit cannot play files recorded using packet write.
≥Depending on how you create MP3 files, they may not play in the order you
numbered them or may not play at all.
6
MP3
ID3
Track
artist
title
name
(Id3 )
(Id3
RM ON
Conserves battery life
Naming tracks and albums
Prefix with 3-digit numbers in the order you
want to play
001track.mp3
Up to 32 characters
ID3 tags are limited to 30 characters
If you create an album like this, the
3
008track.MP3
009track.MP3
files may not play in the order you
numbered them.
The albums would play in the
order 1, 2, 3, 4.
ID3 Track number
track and elapsed
title play time
)
RM OFF
it after recording. The
§
Extension
( or.MP3 )
RQT7722