Miele HG01 Installation Instructions Manual
G 600 / g 800 series dishwasher
Hide thumbs
Also See for HG01:
- Installation instructions manual (40 pages) ,
- Operating instructions manual (56 pages)
Related Manuals for Miele HG01
Summary of Contents for Miele HG01
-
Page 1: Installation Instructions
Installation instructions Dishwasher To prevent accidents and machine damage, read these instructions installation or use. M.-Nr. 05 620 650... - Page 2 ....... . . 3 ......... . 5 Disposal of the packing material .
- Page 3 If there is any doubt concerning in- stallation contact the Miele Techni- Installation, repair and mainte- cal Service Department. nance work should be by a Miele authorized service technician. Work by USA 1-800-999-1360 unqualified persons could be danger- techserv@mieleusa.com ous and could void the warranty.
- Page 4 Before installation, make sure that Ensure that any plastic wrappings, the voltage and frequency listed on bags etc. are disposed of safely the data plate correspond with the and kept out of the reach of babies and household electrical supply. This data young children.
- Page 5 Old machines contain materials which can be recycled. Please contact your The transport and protective packing local recycling authority about potential are environmentally friendly for dis- recycling. posal. Please recycle.
- Page 6 864 mm) are not possible using the supplied legs. For this height range, or for heights greater than 34 " (886 mm), ex- tended legs (part # 02 702 601) are necessary. Contact the Miele Technical Service Department for the appropriate legs.
- Page 7 Machine heights of 35" - 37" (889 - 940 mm) can be obtained if the sup- plied legs are removed and ex- tended legs are attached. Contact the Miele Technical Service Department for the appropriate legs (part # 02 702 601).
- Page 8 Machine heights between 35" and 37" can be obtained if the supplied legs are removed and extended legs are attached. Please contact the Miele Technical Service Department for the appropriate legs (part # 02 702 601). To ensure stability, this dish-...
- Page 9 A stainless steel steam deflector is sup- plied to protect the countertops from steam and condesation when the dish- washer is opened. If the countertop is made of Corian®, granite, marble or other solid, waterproof material, the steam deflector is not required. If the counter is made of different materials, the steam deflector should be positioned so that it cov-...
- Page 10 Stone or marble countertops: The dishwasher must be secured to the adjacent cabinets with fixing angles (part # 03 341 080), available from Miele’s Technical Service Department. ^ Place the skis, with the ratchet at the rear, under the dishwasher legs.
- Page 11 The dishwasher must be installed so that the water and electricity supplies can be accessed through an adjacent cabinet. The supplies must not be lo- cated behind the machine. The floor of the cut out where the dish- washer will be installed should be even in height with the surrounding kitchen floor.
- Page 12 ^ The rear leveling legs can be ad- ^ Adjust the front leveling legs by justed with a T20 Torx screwdriver by pushing on the feet with a slotted turning the screws at the front of the screwdriver. slide skis. ^ Tipping the machine slightly back- wards, if posssible will make adjust- To raise the machine turn clockwise.
- Page 13 ^ Press the "On/Off" button in and place ^ Position the control panel, c, and the cover, a, over the push button. fasten it from the inside of the door, d, using the six screws provided. ^ Insert the drying vent grill, b, into its ^ Align and press the knob onto its opening.
- Page 14 ^ Press the "On/Off" button in and place ^ Position the control panel, c, and the cover, a, over the push button. fasten it from the inside of the door, d, using the six screws provided. ^ Insert the drying vent grill, b, into its ^ Insert the other button covers, e and opening.
- Page 15 ^ Press the "On/Off" button in and place ^ Position the control panel, c, and the cover, a, over the push button. fasten it from the inside of the door, d, using the six screws provided. ^ Push the drying vent grill, b, into its opening.
- Page 16 ^ After adjusting the control panel height, cut off the plastic screw ex- The control panel should be aligned cess. with the drawer fronts of the adjoining kitchen cabinets by adjusting the filler Control Panel Height strips. " control panel with- (112 mm): out filler strips, "...
- Page 17 As long as the panel length calculated is within the Range of Panel Sizes listed, the custom panel should fit with- A custom door panel matching the out a problem. kitchen cabinetry can be installed using the provided templates and bracket. Length: 19"...
- Page 18 A custom door panel must not exceed the listed maximum weight. An over- weight panel will distort the door springs causing the dishwasher door to fall when opened. Plastic control 13 lbs 12 lbs panel (5.9 kg) (5.5 kg) Stainless Steel 10.5 lbs 9 lbs control panel...
- Page 19 ^ Place a template on each end of the ^ Slide the bracket up or down until the mounting bracket as shown, making oblong holes on the machine door sure the rule marks face the outside line up with the oblong holes on the template (shown in inset a).
- Page 20 ^ Tape the bracket to the door panel to ^ Drill pilot holes for the screws using a hold it in place while the mounting " (2.5 mm) bit. holes are drilled. ^ Attach the bracket to the panel using the 6 screws provided.
- Page 21 ^ Push up one side of the door panel until it touches the filler strips (or con- trol panel if filler strips are not used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door. Do not use a power screwdriver.
- Page 22 ^ Remove the bracket from the ma- chine door and place it on the rear of the door panel so that: – the bracket is centered left to right, ^ Hang the bracket on the machine – the bottom of the bracket is door, without the templates.
- Page 23 ^ Push up one side of the door panel until it touches the filler strips (or con- trol panel if filler strips are not being used) and lightly tighten the T20 Torx screws on the corresponding edge of the machine door. Do not use a power screwdriver ^ Repeat the process with the other side of the door panel.
- Page 24 A special fixing angle (part # 03 341 080) must be ordered from If the steam deflector is installed, the your Miele dealer or the Miele Technical mounting bracket holes must align Service Department. with the slots in the steam deflector.
- Page 25 For openings exactly 17 " (45 cm) or " (60 cm) wide: ^ Open the dishwasher door and re- move the caps covering the mount- ing holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adja- cent cabinets using the supplied screws and bushings.
- Page 26 – turn counterclockwise to de- crease the tension. If the door springs can not be adjusted enough (the door falls), the custom door panel is too heavy. Call your Miele dealer or Miele’s Techni- cal Service Department for advice on stronger door spings.
- Page 27 The water inlet hose comes equipped with a 3/4" female hose thread connec- An air gap is built into the water inlet tor. This can be directly connected to a system to prevent potable water from shut off valve with 3/4" MHT (male hose mixing with waste water.
- Page 28 If the standard " copper plumbing for a dishwasher already exists with a com- pression fitting and valve as pictured: Do not cut the intake hose. If the hose is cut, the dishwasher will not work. There will be a water leak and you could be injured.
- Page 29 – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of " (22 mm). Drain hose extensions can be ordered from Miele’s Technical Service Department. – A built-in swivel connector which al- lows the drain hose to be routed in any direction.
- Page 30 If the dishwasher drain hose is con- Since all Miele dishwashers are nected to a equipped with an odor trap and non-re- turn valve, the drain hose can be con- the drain must be nected directly to the drain pipe as il- vented.
- Page 31 The dishwasher comes equipped with a 4 ft (1.2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. THIS APPLIANCE MUST BE Rated load:..12.5 A / 1500 W GROUNDED.
- Page 32 The power outlet for the appliance must For hard wiring, the power cord must be installed within a cabinet, on a wall be disconnected from the terminal box adjacent to the undercounter space in located at the lower left front of the which the dishwasher is located.
- Page 33 ^ Check for any leaks, odd noises and flashing / lit fault indicators on the Once the dishwasher is level and se- control panel. See the "Operating In- cured it should be tested. structions / Frequently asked ques- ^ Remove all packing and literature tions"...
- Page 34 If the door panel hits the toekick when the dishwasher door is opened, the toekick must be cut shorter or recessed deeper. Before installing the toekick, measure- ments must be taken to ensure that the If a decorative or flush mount toekick is desired, and (R) is less than "...
- Page 35 ^ Insert the mounting bracket with the ^ Insert the mounting bracket with the flange pointing toward the center of flange pointing toward the outside of the machine. the machine. ^ Push the mounting brackets in as far ^ Push the mounting brackets in as far as possible by releasing the tension as possible by releasing the tension on the spring clip (see illustration).
- Page 36 The included toekick will fit without modification if the machine is set to its maximum height and the toekick is re- cessed as far as possible (4" / 10 cm). If the machine height is less than maxi- mum, or if the toekick is not recessed 4" (10 cm), the toekick must be shortened.
- Page 37 ^ Carefully open the dishwasher door until it hits the toekick. ^ Using the front lower edge of the door panel as a guide, draw a line across the toekick. ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close to the line just drawn, score the front of the toekick, and snap off the excess, otherwise, trim the toekick along the...
- Page 40 Alteration rights reserved (NovoplusB,P,S) / 000 2401 This bio-friendly paper was bleached without the use of chlorine.