Pioneer Premier PRS-A900 Owner's Manual
Bridgeable four-channel power amplifier
Hide thumbs
Also See for Premier PRS-A900:
- Owner's manual (100 pages) ,
- Owner's manual (44 pages) ,
- Service manual (41 pages)
Related Manuals for Pioneer Premier PRS-A900
Summary of Contents for Pioneer Premier PRS-A900
- Page 1 P,c>n(ffff3(ffff3r sound vision. sou/ BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER AMPLIFICATEUR DE PUISSANCE PONTABLE A QUATRE VOlES Owner's Manual PRS-A900 Mode d'emploi...
-
Page 2: Table Of Contents
Contents Before Using This Product Before Using This Product Thank you for purchasing this PIONEER product. is designed to give you many Information to User years of enjoyment. Important PIONEER SUGGESTS USING A PRO- Visit our website FESSIONAL INSTALLER DUE TO THE CAUTION COMPLEXITY OF THIS PRODUCT. -
Page 3: Visit Our Website
• Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Be DO NOT install or use your Pioneer amplifier sure to protect all cables and important equipment by wiring speakers rated at 4... -
Page 4: Setting The Unit
• When using with an RCA equipped car stereo (standard output of 500 mY), set to the NORMAL position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more, adjust level to match the car stereo output level. -
Page 5: Setting The Gain Properly
• If you decrease the volume of the head unit and set the gain control of the amplifier to the proper position but still the sound cuts out from time to time, contact the nearest authorized PIONEER Service Station. -
Page 6: Connecting The Unit
Connecting the Unit CAUTION • Disconnect the negative (-) terminal of the bat- • Make sure that wires will not interfere with mov- tery to avoid the risk of short-circuit and damage ing parts of the vehicle, such as the gearshift, to the unit. -
Page 7: Connection Diagram
Connecting the Unit Connection Diagram • This diagram shows connections using external output (subwoofer output). Slide the input switch to the left. Special red battery wire [RD-228] (sold separately) After making all other connections at the amplifier, connect the battery wire terminal of the amplifier to Fuse (40 A x 2) the positive terminal of the battery. -
Page 8: Solderless Terminal Connections
Solderless Terminal Connections Connecting the Speaker Output Terminals • Do not connect a cord having an exposed core wire to the power terminals of this amplifier Use a 12 AWG to 18 AWG wire for the speaker wire. (Power terminal, GND terminal, System remote control terminal). -
Page 9: Connecting The Speakers And Input Wires
C"'ollllectillg the Ullit Connecting the Speakers and Input Wires The speaker output mode can be four-channel, three-channel (stereo mono) or two-channel (stereo, mono). Connect the speaker leads to suit the mode according to the figures shown below. Four-channel mode RCA input jack A RCA input jack B Input Select Switch ~..J.. - Page 10 Two-channel mode (Stereo) _----.-=-~::: RCA input jack A In the case of two-channel mode connect ~-I: 7i'~. RCA plugs to the RCA input jack A. "'" .-:J €) <>@ @.., •. ---f. Input Select Switch Slide this switch to the left. •...
-
Page 11: Connecting The Power Terminal
Connecting the Unit Connecting the Power Terminal 2. Connect the wires to the terminal. • Fix the wires securely with the terminal • We recommended that you use the special red screws. battery and ground wire [RD-228], which is sold System remote separately. -
Page 12: Installation
Installation CAUTION CAUTION • Do not install in: To prevent malfunction and/or injury -Places where it could injure the driver or pas- • To ensure proper heat dissipation of the amplifier, sengers if the vehicle stops suddenly. be sure of the following during installation. -Places where it may interfere with the driver, -Allow adequate space above the amplifier for such as on the floor in front of the driver's... -
Page 13: Example Of Installation On The Floor Mat Or On The Chassis
Installation Example of installation on the floor Replacing the terminal cover mat or on the chassis 1. Align the unit and terminal cover, and insert the screw. 1. Place the amplifier where it is to be installed. Insert the supplied tap- 2. -
Page 14: Specifications
Specifications Power source 14.4 V DC (10.8 V to 15.1 V allowable) Grounding system Negative type Current consumption 28 A (at continuous power, 4 n) Average current drawn* 9 A (4 n for four channels) 12 A (4 n for two channels) Fuse 25 A x2 Dimensions... -
Page 15: P.o. Box
TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS OF CANADA, INC. - Page 16 Programme de resolution des plaintes de Pioneer pour resoudre Ie conflil. Ce programme vous est offert sans Irais. Vous devez avoir recours au Programme de resolution des plaintes avant de vous prevaloir de vos droits ou de chercher reparation en vertu du Titre I de la loi Magnuson-Moss Warranty-Federal Trade Commission Improvement Act, 15 U.S.C. 2301 et S.S.
- Page 17 Within 40 days of receiving your complaint, Pioneer will investigate the dispute and will either: (1) respond to your complaint in writing informing you what action Pioneer will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing informing you why it will not take any action.