Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Arbaco PLASMA COOL 14000E
Summary of Contents for Arbaco PLASMA COOL 14000E
- Page 1 Owner’s Manual PLASMA COOL 14000E It is important that you read these instructions before using your new purchase and we strongly recommend that you keep them in a safe place for future reference. Innovative AutoDrain NanoMist Technology ™ Patent Pending...
-
Page 3: Table Of Contents
Table of Contents THANK YOU ………………………………………………………………………… 2 Energy Saving Tips ……………………………………………………………………… 2 SPECIFICATIONS …………………………………………………………………… 3 BEFORE USE ………………………………………………………………………… 4 THE PLASMA COOL UNIT / PARTS ………………………………………………… 5 AUTODRAIN NANOMIST TECHNOLOGY™ ASSEMBLY ………………………… 6 INSTALLATION OF THE WINDOW KIT …………………………………………… 7 Window Kit Installation……………………………………………………………………... -
Page 4: Thank You
Thank You! Thank you for purchasing an Arbaco Portable Air Conditioner. Arbaco is a leading brand in indoor air treatment. We would like you to enjoy the many benefits this unit offers, so please read this manual carefully and take full advantage of the many advanced features that your Arbaco Portable Air Conditioner offers you. -
Page 5: Specifications
Specifications Model PLASMA COOL 14000E Cooling Capacity 14,000 BTU/hr Cooling Power Consumption 1,100 W / 9.8A Dehumidification 80 pints / Day Recommended room size Up to 400 sq. ft. Power Supply 115V / 60Hz / 1 Phase Refrigerant R-22 Compressor... -
Page 6: Before Use
Before Use IMPORTANT! • Leave the unit in an upright position for at least 2 hours before use. • Always place the unit on an even surface. • The power cord has a built-in L.C.D.I. (Leakage Current Detection and Interruption) circuit breaker for added safety. -
Page 7: The Plasma Cool Unit / Parts
The Plasma Cool Unit Parts Air Filter (Pre-installed) Drain Pan Exhaust Hose Remote Control Spiral Water Pipe Slide Bar Adjustable Slide Bar Insulation Strips Connector with Connector Display COOLING 24:00 00:00 08:15 ºF HEAT 06:00 18:00 12:00 HOURS: MINUTES 08:15 TEMPERATURE ºF... -
Page 8: Autodrain Nanomist Technology™ Assembly
AutoDrain NanoMist Technology Assembly Put spiral water Attach Window pipe into hot air Slide Bar flexible hose. Connector to Exhaust Hose by twisting as shown. Connect the Turn the connector female half of the 90 degrees quick connector clockwise until it at the end of the spiral water pipe is locked in place. -
Page 9: Installation Of The Window Kit
AutoDrain NanoMist Technology Installation of the Window Kit Assembly In order for this unit to function properly, it must be vented to the outside. Fitting the Exhaust Hose through a window is easy. Please see below. Adjustable Slide Bar Slide Bar Connector Exhaust Hose... -
Page 10: Installation
Installation WARNING! The length of the exhaust pipe is specially designed according to the specification of this product. Do not extend it with your own hose, as this could cause the unit to malfunction... -
Page 11: Operation
Operation IMPORTANT: The air conditioner should be left in an upright position for at least two hours Reset Button A. Turning the Unit On: 1. Plug the unit into a working electrical outlet. 2. Make sure the green light on the plug is on. Test Button (If not, press the Reset button.) 3. -
Page 12: To Set The Timer
Operation Timer The TIMER function allows you to program the time the unit turns on and turns off. TO SET THE TIMER: • Press the TIME button briefly, the 2 hour digits will flash. • Press the UP or DOWN button to adjust the hour. •... -
Page 13: Canceling The Timer Function
Operation The unit will operate daily according to the timer setting, unless changed. After a power failure, or after the unit has been unplugged, you will have to program the timer settings again. Canceling the Timer Setting In order to cancel the timer programming press the TIME BUTTON. Sleep Mode The SLEEP MODE gradually adjusts the temperature of the unit 4 degrees upward, over a 3 hour period, to meet the needs of a body at rest. -
Page 14: Remote Control
Remote Control To Operate the Remote Control: Insert batteries by pulling down on front cover (See fig. 1). Be sure the remote is pointed at the unit at all times. 1. To Set the Clock: 10:09 • Press the TIME button for 3 seconds. •... -
Page 15: Emptying The Internal Water Container
Emptying the Internal Water Container Note: There are two instances where draining the internal water container may be recommended: 1. In the unlikely event that the Container Full Light on the LCD display flashes 2. Prior to storage of unit. When the internal water container is full, the back light on the LCD display flashes. -
Page 16: Maintenance
NOTE: • Before storage be sure filters are clean and dry. • Should you need to replace filters, contact Arbaco for replacement. • The screen filter must always be used. • The 3M™ High Air Flow filter should be cleaned periodically. Both filters can be vacuumed. -
Page 17: Troubleshooting
If you have any questions regarding the operation of the Plasma Cool please contact Arbaco at 1-877-613-1800 REPLACEMENT FILTERS: To purchase Replacement Filters for this unit, contact Arbaco at 1-877-613-1800 and request model number PLASMA COOL 14000E If this product is defective or not working properly, please DO NOT return to your retail store. - Page 18 Canada Plasma Cool by Arbaco Plasma Cool by Arbaco Arbaco Direct Inc. Arbaco Direct Inc. 2 – 572 5th Street 657 Century Street Pembina, ND 58271 Winnipeg, MB R3H 0L9 1-877-613-1800 1-877-613-1800 www.plasmacool.com www.plasmacool.com...
-
Page 20: Warranty
The provisions of this warranty shall not apply to any product which in Arbaco’s judgment has been (1) subject to misuse or neglect. (2) damaged in an accident. (3) used for a purpose for which it was not designed, or (4) repaired or altered in any way that adversely affected its performance or reliability.
Need help?
Do you have a question about the PLASMA COOL 14000E and is the answer not in the manual?
Questions and answers