ICP MF08B1500A Installation Instructions Manual

ICP MF08B1500A Installation Instructions Manual

Modular blower (electric furnace) with accessory no heat kit

Advertisement

INSTALLATION
INSTRUCTIONS
Models
MF08B1500A
MF12F1900A
MF16J2200A
MF20N2600A
With
AMF001NHA
Accessory
No Heat Kit
Use ONLY factory listed electric heaters.
Modular Blower
(Electric Furnace)
Safety Labeling and Signal Words
Cov
General Information / Installation
............
2
Vertical Installations
........................
2
Horizontal Installations
.....................
3
Condensate
Drain ..........................
5
Refrigerant Orifice and Lines ................
5
Electrical Wiring ............................
6
Checks and Maintenance
...................
7
Blower Performance
........................
8
Safety Labeling
and Signal Words
Danger,
Warning
and
Caution
The signal words DANGER, WARNING and CAUTION
are used to identify levels of hazard seriousness.
The
signal word DANGER is only used on product labels to
signify an immediate hazard. The signal words WARN-
ING and CAUTION will be used on product labels and
throughout this manual and other manuals that may ap-
ply to the product.
DANGER - immediate hazards which WILL result in se-
vere personal injury or death.
WARNING
- Hazards
or unsafe
practices
which
COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which COULD
result in minor personal injury or product or property
damage.
Signal Words
in Manuals
The signal word WARNING
is used throughout
this
manual in the following manner:
The signal word CAUTION
is used throughout
this
manual in the following manner:
CAUTION
Product
Labeling
Signal words are used in combination with colors and/or
pictures on product labels.
Printed in U.S.A.
442 01 2202 02
June 2002

Advertisement

Table of Contents
loading

Summary of Contents for ICP MF08B1500A

  • Page 1 INSTALLATION INSTRUCTIONS Models MF08B1500A MF12F1900A MF16J2200A MF20N2600A With AMF001NHA Accessory No Heat Kit Safety Labeling and Signal Words General Information / Installation .... Vertical Installations ......Horizontal Installations ..... Use ONLY factory listed electric heaters. Condensate Drain ......Refrigerant Orifice and Lines ....
  • Page 2: General Information

    _ Installation Instructions Modular Blower I FigUre ! Nominal Installation Dimensions and Clearances CLEARANCES 14-1/2" (2-2 1/2 Ton) MF08 17-3/4" 31/2 Ton) MF12 21-3/8" (4 Ton) MF16 NO HEATERS 25" (5 Ton) MF20 All Sides ........0" From Supply Duct ......0"...
  • Page 3: Downflow Installations

    Modular Blower Installation Instructions Installations Airflow Positions FigUre 3 The unit is ready to install in any position without modifications. Refer to the coil instructions information on drain UPFLOW DOWNFLOW configurations etc. Make sure coil is set up properly for desired POSITION POSITION position...
  • Page 4: Duct Connections

    Modular Blower I _ Installation Instructions Duct Connections FigUre [ Airflow Positions Supply Duct Supply duct must be attached to the outside of flange on outlet HORIZONTAL RIGHT POSITION end of unit. Flexible connectors may be used if desired. Maintain clearances from supply duct to combustibles...
  • Page 5 Modular Blower Installation Instructions / Electrical Connections Connect field wiring to appropriate terminals on electric heater lugs on the No Heat Kit. All line voltage connections must made with copper wire. Electrical shock hazard. Line Voltage Connection Turn OFF electric power at fuse box or service 1.
  • Page 6 _ Installation Instructions Modular Blower I Low Voltage Control Connections ,gurel Typical Low Voltage Schematic The 24 volt power supply is provided by an internally wired low voltage transformer which is standard on all models. If power Heat Pump with Electric Heat supply is 208 volt, the low voltage transformer...
  • Page 7: Maintenance

    Modular Blower Installation Instructions / Air Flow Check Temperature Rise Check For proper system operation, the air flow through the indoor coil Temperature rise is the difference between the supply and return should be between 350 and 450 cfm per ton of cooling capacity.
  • Page 8 _ Installation Instructions Modular Blower I Airflow Based on no coil, no filter, no electric heat. Deduct heater static shown in heater static table. Deduct coil static, See Coil Specification Sheet. Deduct .20 for Downflow Subbase Kit. SP IN. WG. $P IN.
  • Page 9: Limit Operation

    I Modular Blower Installation Instructions/ Sequence Of Operation Mode Thermostat to Con- Control Control Function trol Board 24 volt State Electric Heat Only Constant Blower / Fan On. ÷ Fan Switch ON) / Fan Off. Thermostat calls for G & W1 & W2 / Fan On, 1st Stage Of Heat On, then 2rid Stage...
  • Page 10 I Installation Instructions Modular Blower I POWER SUPPLY:2081230-I-GO USE COPPER CONDUCTORS ONLY. KEY: HIGH VOLT; LOW VOLT. _F_O- CNTRL p_I--#'MR I]__ _ __-I-Y- Ii __v- _11 __- FAN SPO_BK- L LBL {-_ B R"__y ._Ll --BK'_[_ BASE UNIT WITH NO-HEAT KIT AMFOOINH INSTALLED •SEE INSTALLATION...
  • Page 11: Replacement Parts

    Modular Blower Installation Instructions ReplacementParts 0000 0000 PART PART NUMBBR DESCRIPTION DESCRIPTION NUMBER 1085914 Panel,Side Blower Deck 1082622 C.ontrol, Fan Timer 1082611 1082847 Transformer 1083044 1082848 Motor, Blower 1082849 1083045 1083046 1085371 Bracket, Control Mtg 1085857 1002801 Panel, Top Mount, Blower Motor 1085865 609227...

This manual is also suitable for:

Mf12f1900aMf20n2600aAmf001nhaMf16j2200a

Table of Contents