Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for LG F1409TDS
Summary of Contents for LG F1409TDS
- Page 2 F1409TDS(1~9)
-
Page 3: Table Of Contents
roduct Feature Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley. Water Circulation Spray detergent solution and water onto the load continuously. Clothes are soaked more quickly and thoroughly during wash cycle. The detergent suds can be removed more easily by the water shower during rinse cycle. -
Page 4: Warnings
arnings READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE For your safety, the information in this manual must be followed to minimize WARNING! the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using... -
Page 5: Specification
pecification Drawer Name : Front loading washing machine Power supply : 220-240V~, 50Hz Size : 600mm(W)x 590mm(D) x 850mm(H) Weight : 63kg Max.Watt : 2100W (Wash) / 1100W (Steam) Wash capacity : 8,0kg Water consumption : 52 ( 6,5 / kg ) Permissible water pressure : 0,3-10kgf/cm (30-1000 kPa) -
Page 6: Installation
nstallation Install or store where it will not be exposed to temperature below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. -
Page 7: Installation Place Requirement
nstallation Installation place requirement Level floor : Allowable slope under entire washer is 1˚ Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. -
Page 8: Electrical Connection
nstallation I Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. -
Page 9: Normal Tap Without Thread & Screw Type Inlet Hose
nstallation Normal Tap without thread & screw type inlet hose Unscrew the fixing screw to Push the connector up till the Push the water supply hose attach the tap. rubber packing is in tight contact vertically upwards so that the with the tap. - Page 10 nstallation This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside.
-
Page 11: Level Adjustment
• If possible install the washer in one of the corners of the room, where the floor is more stable. Insert the rubber cups to reduce vibration. You can obtain the rubber cups (p/no.4620ER4002B) from the LG svc dept. Important! •... -
Page 12: Care Before Washing
are before washing Before the first washing Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing. Caring before washing 1. -
Page 13: Adding Detergent
dding detergent Adding detergent and fabric softener 1. The Dispenser Drawer • Main wash only ➔ • Pre Wash + Main Wash ➔ 2. Adding Fabric Softener • Do not exceed the maximum fill line. Close the dispenser drawer slowly. Overfilling can cause early dispensing of the fabric softener which could stain clothes. - Page 14 dding detergent ❋ Tips 3. Detergent dosage Full load : according to • The detergent should be used according to the manufacturer’s recommendation. instruction of the detergent manufacture. Part load : 3/4 of the normal amount. • If too much detergent is used, too many suds Minimum load : 1/2 of full load.
-
Page 15: Function
unction Recommended courses according to the laundry type Water Maximum Load Option Program Fabric Type Temp. (Option) 60°C Color fast garments (shirts, night (Cold, 30°C, Cotton Rating dresses, pajamas...)and lightly 40°C, 95°C) soiled white cotton(underwear) - Intensive Cotton Less than 7.0kg Cotton which is lightly soiled - Pre Wash Quick... -
Page 16: How To Use Washer
ow to use washer 2. Manual Selecting 1. Cotton automatically selected upon power on. • Press the Power( ) button to start. • Select the conditions which you want to • Press the Power( ) button to start. use, by pressing each button. •... -
Page 17: Power/Program
ow to use washer (4) (5) (9) (10) (11) (1) Button : Power (5) Button : Steam Wash (9) Child Lock (2) Dial : Program (6) Button : Temperature (10) Tub Clean (3) Button : Start/Pause (7) Button : Rinse (11) Dial : Spin (4) Button : Time Delay (8) Option... -
Page 18: Time Delay
ow to use washer Start/Pause Time Delay 1. Start Preparing washing before starting “Time Delay” - Turn on the water tap. • This Start/Pause button is used to start - Load laundry and close the door. wash cycle or pause the wash cycle. - Place the detergent and fabric softener in 2. -
Page 19: Refresh Cycle
ow to use washer Steam Wash Refresh I Refresh cycle • For slightly wrinkled clothes which have been stored for an extended time. It just makes wrinkled clothes easy to iron (Do not load wet clothes). • Wrinkles will be reduced. I How to use Refresh cycle 1. -
Page 20: Rinse Hold
ow to use washer Water Temp. Rinse • By pressing the Temp. • By pressing the Rinse button, the water button, the Rinse type can temperature can be be selected. selected. - Cold - 30˚C / 40˚C / 60˚C / 95˚C •... -
Page 21: Medic Rinse
ow to use washer Option Child lock If you choose to lock the buttons on the control assembly to prevent tampering, this function may be selected. By pressing each the button, each function • Child lock can be set by pressing and will be selected. -
Page 22: Tub Clean
ow to use washer Spin Tub Clean Tub Clean course can be set by pressing and holding Intensive and Pre Wash button simultaneously. • By turning the Spin dial, the spin speed can be When Tub Clean course is set, display chosen. -
Page 23: Status Indicator
ow to use washer Display 3. Completion of washing • When washing cycle is completed, “ ” is displayed on the “Multi display”. 4. Time left • During washing cycle, the remaining washing time is displayed. 1. Special function display •... -
Page 24: Maintenance
aintenance ❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. ❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. The water inlet filter - "... -
Page 25: Drain Pump Filter
aintenance The drain pump filter ❋ The drain filter collects threads and small objects left in the laundry. Check regularly that the filter is clean to ensure smooth running of your machine. CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects. -
Page 26: Dispenser Drawer
aintenance Dispenser drawer ❋ After a while detergents and fabric softeners leave a deposit in the drawer. • It should be cleaned from time to time with a jet of running water. • If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out. - Page 27 aintenance The water circulation nozzle & Steam nozzle • Clean the water circulation nozzle and Steam nozzle, if clogged. Cleaning your washer 1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent.
-
Page 28: Troubleshooting Guide
roubleshooting guide ❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. When the machine does not function properly or does not function at all, check the following points before you contact your service provider. Symptom Possible Cause Solution... - Page 29 roubleshooting guide Symptom Possible Cause Solution Washer does not start • Electrical power cord may not Make sure plug fits tightly in wall be plugged in or connection outlet. may be loose. • House fuse blown, circuit Reset circuit breaker or replace fuse. breaker tripped, or a power Do not increase fuse capacity.
- Page 30 roubleshooting guide Symptom Possible Cause Solution • Water supply is not adequate in area Check another tap in the house. • Water supply taps are not completely open. Fully open tap. • Water inlet hose(s) are kinked. Straighten hose(s). • The filter of the inlet hose(s) are clogged. Check the filter of the inlet hose(s).
-
Page 31: Terms Of Warranty
erms of Warranty Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.