Installation Diagram - Mitsubishi Electric MSZ-GE06NA Installation Manual

1-4. INSTALLATION DIAGRAM
ACCESSORIES
Check the following parts before installation.
<Indoor unit>
(1) Installation plate 1
Attachment screws for the installa-
(2) tion plate 5
i4 x25mm
(3) Remote controller holder 1
Screws for the remote controller
(4) holder 2
3.5 x 16 mm (Black)
(5) Battery (AAA) for (6) 2
(6) Wireless remote controller 1
(7) Felt tape (For left or left-rear piping) 1
(8) i Air cleaning filter 2
FIELD-SUPPLIED PARTS
(A) Indoor/outdoor unit connecting wire* 1
(B) Extension pipe 1
(C) Wall hole sleeve 1
(D) Wall hole cover 1
(E) Pipe attachment strap 2 to 5
(F) Screw for (E) 4 × 20 mm 2to5
(G) Piping tape 1
(H) Putty 1
Drain hose
(or soft PVC hose, 19/32 in. [15 ram] 2 to 5
(I) inner diameter or hard PVC pipe
VP16)
(J) Refrigerant oil 1
(K) Power supply cord * 1
* Note:
Place indoor/outdoor unit connecting wire (A)
and power supply cord (K) at least 3 ft. (1 m)
away from the TV antenna wire.
r-
Use the wall hole sleeve i J_.,/Wall hole cover (D)
(C) to prevent indoor/out- Indoor umt _ Seal the wail hole ]
door connecting wire (A) _ ) [.gap with putty (H). J
from contacting metal Wail hole ' FJJ// ,-_
parts in the wall and to sleeve _flach l eh pipe.to|
protect the wiring from ' ' _/_i_,_ wall whlh prpe a/- |
rodents, i//ii F_ [lachment strap (E). l
CxUt/rOff t he Pipe attachment
length
_ap (E)
Attachment screw (F)
k.
__ (After the leak test, apply insulating mate-)
[_///_--_7) (C) ! "When the piping is to be attached to a wall
_b<._i_:_ I _ _"(G) comprised of tin plate or metal netting, use
,_,"_ chemically treated wooden piece 25/32 in.
1_1 ( ]_¢ (20mm)orthickerbetweenthewalland
(6_ _ the piping or wrap insulation vinyl tape 7
I _ "_ I ( )_ .G-,[]_(3) to8turns around the piping.
_ff .._.._ _._ To use existing piping, perform COOL
k
operation for 30 minutes and pump down
(4) before removing the old air conditioner.
Remake flare according to the dimension
for new refrigerant.
<GE09/12/15>
Basically open 4 in.
(100 mm) or more
without any obstruction
in front and on both
sides of the unit.
Orr_r_ )
(100 ram)
or more
(I)
Open two sides of left,
right, or rear side.
Unit: inch
31-1/2
5t_ 19-11/16
43- Air inlet _[
/ _ II1-g/16
Air outlet
2-3/8 x 13/16 slot
Unit: mm
8OO
1150 500 I
_ 43 Air inlet _
/ "_ 1140
/ Air outlet
2-10 x 21 slot
Units should be installed by licensed contractor]
[accord ng to oca code requ rements. J
<GEl8>
20 in. (500 mm)
(K)
. (A)
Unit: inch Unit: mm
64o
r--€---_ Air i nlet _
_ gQ----
_[d_ Air outlet _]_
4-3/8 x 13/16 slot 1-18/32 - 40
Drain piping for outdoor unit
Install the unit horizontally.
Do not use drain socket in cold regions. Drain may freeze and make the fan stop.
The outdoor unit produces condensate during the heating operation. Select the installation place to ensure to prevent the outdoor unit and/or the grounds from being wet by drain
water or damaged by frozen drain water.