Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Manhattan MSKL MS-3020
Summary of Contents for Manhattan MSKL MS-3020
- Page 1 User Guide MSKL MS-3020 MSKL MS-3020 User Manual...
- Page 2 3. Plug the equipment into an outlet on a circuit different from that to which the receiver is powered. 4. Consult MSKL or an experienced radio/television technician for help. All external connections should be made using shielded cables. MSKL MS-3020 User Manual...
-
Page 3: Chapter 1 - Introduction
Power: AC input voltage 47 ~ 63Hz, 100 ~ 127V/3A, 200 ~ m240V/1.5A, 162W 1.4 Hardware Requirement The MSKL MS-3020 needs a host system with SCSI LVD interface or Ultra2 Wide or higher standard. 1.5 Package After opening the package, check the following items: •... - Page 4 SCSI bus, an electrical pathway that consists of adapters and devices, there should be installed a terminator at the end of the bus. No matter how many SCSI devices (up to 15) are attached to the bus, a terminator must be added to the last device. MSKL MS-3020 User Manual...
-
Page 5: Chapter 2 - Installation
Access Signal LED No light: No access Green light: Online Secondary Slave HDDs Red light: Offline Power Signal LED Blinking red light: Bad sector Secondary Slave HDDs Yellow light: Access Access Signal LED No light: No access MSKL MS-3020 User Manual... -
Page 6: Set The Scsi Id
MS-3020, lower the speed to 40MB/s. 4. Pin 4: SCSI Host Transfer Rate at 160MB/s The default is off, but if pin 4 is adjusted to ON, the highest transfer rate will reach 160MB/s. MSKL MS-3020 User Manual... - Page 7 2. Pull the handle to let the tray out. Figure 2-5 3. Put a hard disk drive into the tray. Figure 2-6 4. Turn the tray, fasten with 4 screws and put it back into the MS-3020. Figure 2-7 MSKL MS-3020 User Manual...
- Page 8 Use SCSI LVD cables to connect two or more MS-3020, and add a terminator to the last MS-3020. See figure 2-9 and refer to 2.2 for installing more MS-3020. Host External SCSI Port MS-3020 SCSI Ports Terminator Figure 2-9 MSKL MS-3020 User Manual...
- Page 9 2. It is invalid to adjust DIP switch during operation. Before changing the setting, power off the host PC and the MS-3020 first. You had better set JBOD or Normal mode right in the beginning. The later change may damage the stored data. MSKL MS-3020 User Manual...
-
Page 10: Chapter 3 - Troubleshooting
Re-plug the IDE cables and the status signal lines, which are 3-pin color cables connecting to CN6. • Replace the hard drive if the red LED still lights. • Contact the distributor if the problem still exists. Figure 3-1 MSKL MS-3020 User Manual... - Page 11 Choose “Disk Management” under “Storage”, and a given hard disk drive ID will appear on the right lower corner of the windows. • If the newly installed hard disk drive doesn’t appear on the screen, it might be improperly installed or damaged. Try again. MSKL MS-3020 User Manual...
- Page 12 1. Put the support CD into CD-ROM, and find the program by the following path: E:\Utility\Bridge_Smart_Uti\Setup.exe 2. Click “Next” to install according to the instructions of the setup wizard. 3. Execute the program from Start\Programs\SCSIDE Firmware Utility. MSKL MS-3020 User Manual...
- Page 13 150L. If the old versions alphabet is L, you should choose a new version with L, too. 5. Click “Update SCSIDE Firmware”, choose the new firmware, and click “Open”. The System will ask if you want to update. Click “Yes”. The successful update is as the following figure shows. Re-boot your system. MSKL MS-3020 User Manual...
Need help?
Do you have a question about the MSKL MS-3020 and is the answer not in the manual?
Questions and answers