Contents Names of the parts Safety precautions Installation and adjustment Installation of the major function Preparation before washing The musts in washing Usage of the detergent Washing sequence Disposal after washing Trouble-Shooting Answer to question Packing list *Specification...
Names of the parts Waterproof cover Spin timer Wash selector Wash timer Water-filling entrance cover Water-filling entrance Water-filling entrance Water inlet selector handle Control panel Cascade outlet Filter frame Wash tub cover Meaning and description of the symbols Warning sign Forbidding sign Please check if the power receptacle has good earthing condition before using to guarantee your safety.
Safety precautions Please insert the power cord into special receptacle with rated vol- tage.Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector. If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department.
Safety precautions Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine.
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Usage of the drain hose The drainage shall be smooth with the drain hose. 1.put the drain hose up to suitable position.
How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Extend the drain hose from the side of spin tub Put soft items on the ground. Lean the machine down gently with the front surface facing the ground.
Introduction of the major function Cascade washing During washing, water will be arised from the bottom of tub and spraying out just like waterfall flow strongly outside, thus make the detergent quickly and completely dissolved more than commonly washing method. Strong water flow sprayed will impact laundries strongly to improve washing efficiency.
Preparation before washing Pay attention to followings before washing the laundries Check if Clear the Tie the long the laundries pocket. Take strips; fasten has special out the coins, the buttons; requirement sand, hairpins close zippers. on washing etc. a. Check if the laundries are applicable for washing with machine. b.
The musts in washing Usage of the detergent How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laun- dries with color or pattern as they are prone to lose color.
Washing sequence Wash timer Water inlet (To set to below 2 minute, entrance first set to 5 minute then turn it back. It can increase the service life of the timer). Wash 1.Water-filling selector Set the water inlet selector at the "WASH" side. (Figure 1) 2.
Midway spinning Put the laundries into the spin tub evenly and smoothly. Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland The laundries Proper are slanting (2) Close the inner and outer cover of the spin tub. (3) Spin for 1-2 minutes.
Rinsing Rinse with stored water 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is below 4.0 kg, please use "Standard" current. If you use "Strong"...
Spinning 1. Put the laundries into the spin tub evenly and smoothly. 2. Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3. Spin Select suitable spin time according to the laundries, and do spinning. During spinning, if there's abnormal sound, it is generally owing to slanting placement of the laundries.
Disposal after washing After using, please clean the lint and foreign materials of the lint filter and lint frame in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing.
Cleaning the filter frame 2. Cleaning the filter frame Clean the lint around the frame and flush with tap water. 3. Install the filter frame. (1).Insert the mounting plate at the bottom of the frame into the valve cover. (2).Hang up the hook at the left upper side.
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
Packing list Name User's manual Water inlet hose Lint filter Gland Twin-tub washing machine Specification Water level Water quantity about (L) Maximum/79 Medium/66 Minimum/48 Rated washing capacity(kg) Rated spinning capacity(kg) Injection pressure(MPa) Quantity One piece One piece One piece One piece One set 0.02~0.2...