Advertisement
Quick Links
Installation
instructions
Do This First
(for existing sleeve)
Note that the air conditioner dimensions are: 24.wide,
14½.high,
and 18½.
deep (without front). Install Air
Conditioner according to these installation instructions
to achieve the best performance. Save these installation
instructions for future reference.
Items in Kit
You may not need all parts in the kit. Discard unused
pans.
Qty.
Tapered Spacer Blocks
17,,Long
2
Centering/Support Blocks
4½.x 3½.x 1½.
4
Plastic Divider
1/8" x 4½.x 14½,,
2
Stuffer Seal
1 . x 1½"x 84,,
1
Seal
1½.x 1½.x 25,,
3
Seal
1½,,x 1½.x 14,,
2
Seal
1½.x 3/8.x 25.
3
Seal
1½.x 3/8.x 14,,
2
Seal
1" x 3/4.x 14,,
2
Trim Frame (side legs)
2
Trim Frame (top & bottom legs)
2
Ground Wire (green)
1
Nut for grounding screw
1
Grounding Screw
1
Grille (plastic)
1
Grille Aluminum
1
Nuts (plastic)
4
Screw w/washer
4
How to Install
1. identifythe wall-sleeve brand for your installation,
from the chart below.
Brand
White-Westinghouee
Frigidaire
Carrier (52F Series)
General Electric/
Hotpoint
Whirlpool
Wall Sleeve Dimensions
(inches)
Width
Height
Depth
}25½
15¼
17½
16,
or 22
26
15%
25¼
16½
Fedders/Emerson
27
16¾
16'/,
17½
or 23
16¾
or 19¾
18%
15
18%
16¾
Sears/Kenmore
25¾
16½
Emerson/Fedders
26¾
15¾
Carrier (51S Series)
25¾
167/,
Friedrich
27
16¾
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition and
have a rear grille that securely attaches to sleeve, or
rear flange that serves as a stop for the Air Conditioner.
CAUTION: When installation is complete, replacement
unit MUST have a rearward
slope as shown.
1/4" 1o 5/16"
81eeve
REAR
L
2. Remove old Air Conditioner from wall sleeve and
prepare wall sleeve as follows:
-- Clean interior (do not disturb seals).
-- Wall sleeve must be securely fastened in wall before
installing Air Conditioner. Drive more nails or screws
through sleeve, into wall, if needed.
-- Repair paint if needed.
3. If not existing, drill a 3/16.clearance
hole for ground-
ing screw through left side of wall sleeve, in a clear area
about 3 inches maximum (to suit) back from front edge
of sleeve as shown below. Next attach ground wire inside
sleeve, using grounding screw, nut washer pull loose
end of ground wire out front of sleeve, and temporarily
bend it down and around lower edge of sleeve.
Wall sleeve to unit
sleeve grounding
J
3/16"
F
Hole
4. Prepare the wall sleeve for installation of the new unit
per the following Brand instructions.
#1 Emerson
#2 Fedders
#3 Fedders or Friedrich
#4 General Electric/Hotpoint
#5 Sears or Carrier (51S Series)
#6 Whirlpool
#7 Whirlpool
#8 White-Westinghouse/Frigidaire/
Carrier (52F Series)
#9 White-Westinghouse/Frigidaire
15"Deep
l_A,,Deep
16¾,,Deep
16¼,,Deep
18%,,Deep
17'_,,Deep
23.Deep
16,,+ 17½.Deep
22"Deep
5. Install new unit into wall sleeve.
6. To attach ground wire to the new unit, remove the
screw from the left side front.
7. Assemble and installthe
Trim Frame (see instruction).
P/N 66129901165
Advertisement
Related Manuals for Frigidaire FAH10ES2TA12
Summary of Contents for Frigidaire FAH10ES2TA12
- Page 1 18%,,Deep }25½ 15¼ 17½ Carrier (52F Series) or 22 #6 Whirlpool 17'_,,Deep General Electric/ #7 Whirlpool 23.Deep 16'/, Hotpoint #8 White-Westinghouse/Frigidaire/ 16,,+ 17½.Deep 17½ 25¼ 16½ Whirlpool Carrier (52F Series) or 23 #9 White-Westinghouse/Frigidaire 22"Deep 16¾ Fedders/Emerson 16¾ or 19¾...
- Page 2 This unit's increased performance characteristics result from having two rear air intakes, it is very important that these installation instructions are followed so your unit can operate at maximum efficiency, if this is an existing sleeve, and there is an existing rear grille, it needs to be replaced by the ones shipped with the unit in the accessory kit.
- Page 3 15"Deep Wall Sleeve Brands: #1 Emerson 1. Redirectthe louversat the back of the wall sleeve as shown opposite. The use of pliersis recommended. TopView 2. Attach (1) 1 ½" x 3/8" x 25" long seal in the center at the top of the sleeve.
- Page 4 Wall Sleeve Brands: #2Fedders 19 _" Deep 1. Redirect the louvers at the back of the wall sleeve as shown RearLoavam opposite. The use of pliers is recommended. ao_\ 3.5 I_O* TopView 2. Attach (2) 4 ½" x 3 ½" x 1 ½" centering/support blocks one on each side wall.
- Page 5 #3 Fedders or Friedrich 16 %" Deep 1. Redirect the louvers at the back of the wall sleeve as shown opposite. The use of pliers is recommended. 2. Attach (2) 4 ½" x 3 ½" x 1 ½" centering/support blocks one on each side wall.
- Page 6 Wall Sleeve Brands: El ,-tra/Hotpoint 16 7/8" Deep #4 General 1. Redirect the louvers at the back of the wall sleeve as shown Louvom opposite. The use of pliers is recommended. T{_ V_w 2. Cut (2) 17" Tapered Spacer Blocks as shown below into two pieces.
- Page 7 185/8. Deep WaJJ SJeeve Brands: #5 Sears or Carrier 51S Series 1. Redirect the louvers at the back of the wall sleeve as shown opposite. The use of pliers is recommended. TopView 2. Install (2) tapered spacer blocks to the floor of the sleeve as shown.
- Page 8 Wall Sleeve Brands: #6Whirlpool 17 1/8" Deep 1. Redirect the louvers at the back of the wall sleeve as shown Lou_am opposite. The use of pliers is recommended. 3"5'_ I _o F4_O = Top_ew 2. Cut (2) 17" Tapered Spacer Blocks as shown below into two pieces.
- Page 9 Wall Sleeve Brands: #TWhirlpool 23. Deep LOgVeI_ 1. Redirect the louvers at the back of the wall sleeve as shown opposite. The use of pliers is recommended. GO o f 80 ° \\ \ \ \_ _////JJ/J \\_\\_\_\\I/111// Because of the increased unit depth, first try dry fitting using the method described below: 1.
- Page 10 #8 White Westinghouse/Frigidaire/ 16" + 17 ½" Deep Wall Sleeve Brands: Carrier 52F Series If the wall sleeve does not have a rear grille or Iouvered panel, installthe plastic grille from the kit. The plastic grille is mounted to the inside of the wall sleeve at the rear flanges.
- Page 11 #9 White Westinghouse or Frigidaire 22. Deep Wall Sleeve Brands: if the wall sleeve does nothave a rear grille or Iouvered panel, install the plastic grille from the kit. The plastic grille is mounted to the inside of the wall sleeve at the rear flanges.
-
Page 12: Finishing Installation
FINISHING INSTALLATION: 1. Install the 1" x 1 ½" x 84" long stuffer-seaJbetween the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble the trim fTame by inserting top and bottom peieces into side pieces and snapping into place. 3.