Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
installation instructions
For Slider Casement Air Conditioners
NOTE:
These instructions
describe
installation
in a typical wood framed window
with a wood SLIDE-BY
sash,
or installation
in a metal CASEMENT
window.
Modification
may be necessary
when installing
in windows
made
differently
than those shown in these instructions.
A high window
accessory
kit is available
for window
heights up to 62" (1575mm).
Part # EA103W.
TABLE OF CONTENTS
SUBJECT
PAGE
1
2
2
4
7
8
Meeting
Electrical
Requirements
OBSERVE
ALL LOCAL
GOVERNING
CODES
AND ORDINANCES.
DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE
THE POWER SUPPLY
CORD
GROUNDING
PRONG,
NOTE:
If codes permit, and a separate
grounding
wire is used; it is recommended
that a
qualified
electrician
determine
that the grounding
path is adequate
and not interrupted
by plastic,
non-metallic
gaskets,
or other insulating
materials.
RECEPTACLE
WIRING
Receptacle
wiring should
be a minimum
of 14
gauge. Use copper wire only. It is your responsibility
to provide
proper and adequate
receptacle
wiring,
installed
by a qualified
electrician.
ELECTRICAL
REQUIREMENTS
A 115 volt (103.5 minimum,
126.5 maximum),
60
Hertz, AC only, 15 ampere
fused electrical
supply
is required.
Atime
delay fuse or time delay circuit
breaker is also required.
A separate
circuit, serving
only this appliance,
MUST be provided.
P/N 66129901161
Advertisement
Related Manuals for Frigidaire FAK085R7V11
Summary of Contents for Frigidaire FAK085R7V11
-
Page 1: Table Of Contents
installation instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT window. Modification may be necessary when installing in windows made differently than those shown in these instructions. -
Page 2: Electrical Connection
Electrical Connection Electrical ground is required on this appliance. 3 Prong Grounding Type Wall Receptacle Recommended grounding method: 3 Prong For your personal safety, this appliance must be Grounding Plug grounded. This air conditioner includes a power supply cord with a 3-prong grounding plug. - Page 3 1. Makesureyou haveallthe necessaryparts. Installation kit contents: Platform(1) Supportbrace(1) Adjustmentbolt (1) Hexflangenut - 1/4"(1) Trackseal (1) Sidechannelseal (1) Foamsealstrip/Sashseal Safetybracket(1) 9-11. Screw- #10x2-1/2"flat-head(2), OR Screw- #10xl-314" p an-head(2),OR Screw- #10xl"pan-head(2) 12. Screw- #8x314" p anhead (6) 13. Screw- #8-32x314" s elf-threading (7) 14.
-
Page 4: Installing Unit In A Sliding Window
Choose the proper window location. Choose a window that allows the cooled air to flow freely and directly into room(s) you wish to cool. Remember, it is difficult to move air around corners. Also, choose a window that is within 6 feet of an electrical outlet. - Page 5 Apply track seal 4. Peel off protective backing from track seal. Apply to window side seal to room side of window track. Center of seal strip should coincide with the line marked in Step 2. The two screw holes drilled in Step 3 should be directly above seal strip in the inner track.
- Page 6 10. Clamp plastic window panel betweena board anda work table,andcut alongcuttingline with a fine tooth saw.Removeany burrswitha file. Fastening Side Channels 11. Fasten side channels to the sidesof the AC using3 screws(Item 17)per channel.Startwith first screwat top of channel.Makesure hookendsof channelsfacetowardbackof unit.
-
Page 7: Alternate Window Jamb Applications
16. Slide inner window sash firmly against side of the cabinet. Make sure not to peel the seal strips from the window track and cabinet side channels. the panel frame does not fit snugly to the inner window sash, secure the panel frame to the sash with #8x3/4-inch screws, or #8-32x3/4-inch... -
Page 8: Installing Unit In A Casement Window
Installing the Unit in a Casement Window NOTE: Open the window the maximum amount allow for clearance of the cabinet. The crank handle should be removed to allow the platform to be fastened to the jamb. If the window cannot open far enough (more than 15-112 inches) for the cabinet to clear the window,... - Page 9 Rear is at ]east 5. Adjust the platform assembly so that the rear of 7/16" lower the air conditioner will be 3/16-inch lower than the than front front. This ensures proper water drainage from the air conditioner. NOTE: A projection below the base of the air conditioner will require the rear of the platform...
- Page 10 11. Cut side channel seal into 2 equal lengths. Remove the protective backing and apply it to the rear side of the cabinet side channels, starting just below the panel frame assembly. Pinch off excess length so the seal is even with the bottom of the cabinet side channel.