Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
iNSTALLATION
AND SERVICE
MUST BE PERFORMED
BY A QUALiFiED
iNSTALLER.
iMPORTANT:
SAVE FOR LOCAL
ELECTRICAL
iNSPECTOR'S
USE.
READ AND SAVE THESE
iNSTRUCTiONS
FOR FUTURE
REFERENCE.
Clearances
and Dimensions:
1.
Provide
adequate
clearances
between
the range and adjacent
combustible
surfaces.
2.
Location--Check
location
where the ranqewill
be installed.
Checkforproperelectrical
supply, and the stability ofthefloor.
3.
Dimensions
that are shown must be used. Given dimensions
provide
minimum
clearance.
Contact
surface
must be solid
and level.
...................
Minimum
to
wall
on either
1"-_
side of range
above
36" height.
t
Minimum
to
18" cabinets on
either side
_
of range.
Fig. 1
SIDE
VIEW
1÷13"÷1
Maximum
depth
r
for cabinets
(/'
above range top.
_25"_
I_--
30"
_
0" clearance
below
cooking
top and at rear of range.
RANGE
OVERALL
DIMENSIONS
Fig. 2
47-3/4"
Maximum
44 s/8" \
253/4"
30-1/8'
Centerline
of range
q_
t
i
I
dimensions for electrical
I
outlet location are maximum.J
1
I
I
Dashed cubed area
'
shows where the electrical
I
,
outlet must be installed
I
:or flush to the wall installation
- 111"
t
I
ii
I-'I
......
i
"<- . .......
0"
2-5/8"
for models
equipped
with warmer
drawers"
3-I/2'
for models
equipped
with
storage
drawers
Wall
Edge
Fig. 3
*30" MINIMUM CLEARANCE
BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OF AN UNPROTECTED
WOOD OR METAL CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED
BY NOT LESS
THAN 1/4" FLAME RETARDANT
MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS
STEEL, 0.024" ALUMINUM OR 0.020" COPPER. 0" CLEARANCE
IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL
DIMENSION REQUIREMENTS
PROVIDED ABOVE TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND
INCORRECT
COUNTERTOP
AND CABINET CUTS.
TO ELIMINATE THE RISKOF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED
ABOVE TH ESURFACE UNITS SHOU LD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, TH E RISK CAN BE REDUCED BY
INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY
A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
Serial Plate Locations:
Serial plate is located on the
lower right front frame of the
appliance.
Alternate
location
may be under cooktop.
pin 316454926(1111)
Advertisement
Related Manuals for Frigidaire FFEF3017XSA
Summary of Contents for Frigidaire FFEF3017XSA
- Page 1 iNSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. Clearances and Dimensions: Provide adequate clearances between the range and adjacent combustible surfaces. Location--Check location where the ranqewill be installed.
- Page 2 iMPORTANT SAFETY iNSTRUCTiONS NORMAL INSTALLATION STEPS Anti=Tip Bracket Installation Instructions = Tip Over Hazard IMPORTANT SAFETYWARNING A child or adult can tip the range and be To reduce the risk of tipping of the range, the range must killed. be secured to the floor with a properly installed Anti-Tip Verify the anti-tip device has been Bracket and screws packed with the range.
- Page 3 2b. For models requiring a power supply cord kit - RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF AN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION INSTRUCTIONSARE NOT FOLLOWED OR STRAIN RELIEF BRACKET IS DISCARDED. This appliance may be connected by means of a power supply cord.
- Page 4 4. Power cord installation. This appliance must be connected to a power source with a power cord. Before wiring the range review the suggested power source Strain location drawing in Fig. 3. Relief Follow the manufacturer's installation instructions supplied with the strain relief and install (also refer to Figs.