Advertisement
Quick Links
Download this manual
See also:
Use and Care Manual
INSTALLATION
AND SERVICE MUST BE PERFORMED
BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL
INSPECTOR'S
USE,
READ AND SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
If the information
in this manual is not followed
exactly, a fire or explosion
may result causing
property
damage, personal injury or death.
FOR YOUR
SAFETY:
Do not store or use gasoline
or other flammable
vapors
and liquids
in the vicinity
of this or any other appliance.
--
WHAT TO DO IF YOU SMELL
GAS:
• Do not try to light any appliance.
• Do not touch
anyelectrical
switch;
do not use any phone
in your building.
• Immediately
call your
gas supplier
from
a neighbor's
phone.
Follow
the gas supplier's
instructions.
• If you
cannot
reach
your
gas
supplier,
call
the
fire
department.
--
Installation
and service
must be performed
by a qualified
installer,
service
agency
or the gas supplier.
• ALL RANGES
CAN TIP
• INJURYTO
PERSONS
COULD RESULT
• INSTALL ANTI-TIP
DEVICE PACKED WITH
RANGE
• SEE INSTALLATION
INSTRUCTIONS
RANGE
OVERALL
2 5 3/4'
VIEW
DIMENSIONS
_1_
30-1/B"
_1_
Minimum
to
Wail on Either
Side of Range
Above 36"
Height,
* Note: 3"
Clearance
SIDE
VIEW
E
C
Minimum
to
. _aonne[5
on
Maximum
Depth
1_
Either Bid e
for Cabinets
[_]
of Range.
Above Range Top.
_25i_
ii
O"Clearance Beiow Cooking Top and at Rear of Range.
Clearances
and Dimensions
Provide
Proper
Fuel Type
1.
Location--Check location where
Before Proceeding: Your range is preset to operate on natural gas only. Some
the ranaewill be installQd, Check
models are shipped convertible with parts and conversion instructionssupplied.
for proper electrical
and gas
Other models have
a LP/Propane
Conversion Kit available
through
your dealer.
supply, and the stability of the
floor.
2.
Dimensionsthatareshownmust
[Ft_[_TJ'_DONOTattempttoeonvertthisrangetoLP/Propanesettingswitheut
be used.
Given
dimensions
theproperLP/Propaneconversionkitprovidedwiththerangeorobtainedfromyour
provide
minimum
clearance,
dealer. Follow all instructionsprovided with the conversion kit.
Contact surface must be solid
and level.
Espa6ol - Pages 9-16
P/N 316259315 (0112)
1
Advertisement
Related Manuals for Frigidaire FGF355ASA
Summary of Contents for Frigidaire FGF355ASA
- Page 1 INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE, READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
-
Page 2: For Models With Self-Clean Feature
Stepping, leaning or sitting on the doors Important Notes to the Installer or drawers of this range can result in serious injuries and Read all instructions contained in these installation can also cause damage to the range. instructionsbefore installingrange. Removeall packingmaterial from theovencompartments •... -
Page 3: Before Starting
Before Starting Locate the Bracket Using the Template- (Bracketmay be locatedon eitherthe left or rightside ofthe range. Use Tools You Will Need the information below to locate the bracket iftemplate is For leveling legs and Anti-Tip Bracket: not available). Mark the floor or wall where left or right side ofthe rangewillbe located. - Page 4 Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. Note: A minimum clearance of 1/8" is required between the bottom of the range and the leveling leg to allow roomfor the bracket. Use a spiritlevel tocheck youradjustments. Slide range back intoposition.
- Page 5 Manual Flare Flexible Flare Union Pressure 5. Read electrical connection details below SvhU_Oeff Union Appnli_ n _t e Adaptor Regulator and connect electricity to range. Before servicing, disconnect electrical supply at circuit breaker, fuse or power cord. ServiceShut-Off ValveElectricIgnition rro_ls on y_ Electric Requirements: An individual, properly grounded and (Shown in ON Position).
- Page 6 Electric Ignition Surface Burners Operation of Surface Burners Operation of electric igniters should be checked after range Installation of Burner Cap Assembly and supply line connectors have been carefully checked for Your range is equipped with any combinationof the sealed leaks and range has been connected to electric power.
- Page 7 8. Adjust the "LOW" Setting of Surface Burner After removing all packing materials and literaturefrom the Valve (Linear Flow Valves Only): oven: a) Setoven to BAKE at300_F. See_for operating instructions. b) Within 60 seconds the oven burner should ignite. Check for proper flame, and allow the burner to cycle once.
- Page 8 If removing the range isnecessaryforcleaning or maintenance, shut off gas supply. Disconnect the gas and electrical supply. If the gas or electrical supply is inaccessible, lift the unit Oven Bumer slightly at the front and pull out away from the wall. Pull only Tube as far as necessary to disconnect the gas and electrical supply.