Table of Contents
Advertisement
8. Adjustthe
"LOW"
Setting of Surface Burner
Valve (Linear
Flow Valves Only):
To
Surface
Burner
Test to verify if "LOW" setting should be adjusted
a.
Push in and turn control to LITE until burner ignites.
b.
Push in and quickly turn knob to LOWEST POSITION.
c.
If burner goes out, reset control to OFF.
d.
Remove the surface burner control knob.
e.
Insert a thin-bladed screwdriver into the hollow valve stem
and engage the slotted screw inside. Flame size can be
increased or decreased with the turn of the screw. Turn
counterclockwise
to increase flame size. Turn clockwise
to decrease flame size.
Adjust flame until you can quickly turn knob from LITE to
LOWEST POSITION without extinguishing the flame. Flame
should be as small as possible without going out.
Burner Flame Size
_l
5/8" i_
S
Main
Top
Note:
Air mixture adjustment
is not required on surface
burners.
Operation
of Oven Burners and
Oven Adjustments
9.
Electric Ignition Burners
Operation of electric igniters should be checked after range
and supply line connectors have been carefully checked for
leaks and range has been connected to electric power.
The oven burner is equipped with an electric control system
as well as an electric oven burner igniter. If your model is
equipped with a waist-high broil burner, it will also have an
electric burner igniter. These control systems require no
adjustment. When the oven is set to operate, current wilt flow
to the igniter. It will "glow" similar to a light bulb. When the
igniter has reached a temperature sufficient to ignite gas, the
electrically controlled oven valve will open and flame will
appear at the oven burner. There is a time lapse from 30 to 60
seconds after the thermostat is turned ON before the flame
appears at the oven burner. When the oven reaches the dial
setting, the glowing igniter will go off. The burnerflame will go
"out" in 20 to 30 seconds after the igniter goes "OFF." To
maintain any given oven temperature, this cycle will continue
as long as the dial (or display) is set to operate.
After removing all packing materials and literature from the
oven:
a)
Set oven to BAKE at 300°F. See Use & Care Manual for
operating instructions.
b)
Within 60 seconds the oven burner should ignite. Check
for proper flame, and allow the burner to cycle once.
Reset controls to off.
c)
If your model is equipped with a waist-high broiler, set
oven to BROIL. See Use & Care Manual for operating
instructions.
d)
Within 60 seconds the broil burner should ignite. Check
for proper flame. Reset controls to off.
10. Air Shutter-Oven
Burner
iLower
Oven Baffle
_emovable)...--"
Waist-High Burner
(Self Clean Models)
<_Air
Shutter
Lower Oven Bottorr
(Removable)
/
The approximate flame length of the oven burner is 1 inch
(distinct inner, blue flame).
To determine if the oven burner flame is proper, remove the
oven bottom and burner baffle and set the oven to bake at
300°F.
To remove the oven bottom, remove oven hold down screws
at rear of oven bottom. Pull up at rear, disengage front of oven
bottom from oven front frame, and pull the oven bottom out
of the oven. Remove burner baffle so that the burner flame
can be observed.
If the flame is yellow in color, increase air shutter opening
size. (See "2" in illustration below.) If the flame is a distinct
blue, reduce the air shutter opening size.
To adjust loosen lock screw (see "3" illustration
below),
reposition air shutter, and tighten lock screw. Replace oven
bottom.
7
Advertisement
Table of Contents
