Download Print this page

Advertisement

INSTALLATIONAND SERVICE MUST BEPERFORMED BY A QUAUNED INSTALLER.
IMPORTANT:SAVEFORLOCAL ELECTRICAL INSPECTOR'S USE.
READAND SAVETHESEINSTRUCTIONS FOR FUTUREREFERENCE.
FOR YOUR SAFETY: Do not store or use gasoline or other flammable
vapors and Hquids in the
v[dnity
of this or any other appliance.
GENERAL iNFORMATION
Tile Warmer Drawer carl be used:
As a stand alone applian(e
As a combination Warmer Drawer with a 30" (76 cm) builtqn oven mounted above
IMPORTANT: The warmer drawer must be installed on a surface leveled from left to right, rear to front and the surface
must be capable of supporting 100 pounds (45 Kg).
Warmer Drawer
Dimensions
'
BI
C; D EPTH
i
i
10"(25,4cm)
30"(76,2cm)
23 3/8"(59,4cm)
I
I
HEIGHT
WIDTH
'
DEPTH
Min.
8 3/8"(21,3cm)
28 1/2" (72,4cm)
24"(61 cm)
Max,
8 5/8"(21,9cm)*
28 3/4" (73cm)
IMPORTANT:
The Warmer
Drawer runs off a single
phase three-wire
120 volt, 60 hertz, AC only electrical
supply with ground.
Combination
Warmer
Drawer/
30" (76 cm) Built-in
Oven installation
Caution:
Two 3" (7,6 crn) wide X 3/
4" (1,9 cm) thick planks have to be
installed and they should be able to
support 200 pounds, (90,7 K,
H* =10-1/8" (25,7 cm) Min. is a @iticai
dimension
and must be applied.
£ HEIGHT
10"(25,4cm)
30"(76,2cm)
23 3/8"(59.4cm)
Note: It is also possible to install this warmer drawer in a
height opening of 91/4" (23.5 cm). Please refer to page 3
for complete instructions.
Printedin Unit_dStat_s
P/N 318201804
(O412) Rev, C
English - pages 1-4
Espafio[ - pBginas 5-8
Frangais - pages 9-12

Advertisement

   Related Manuals for Frigidaire PLEW30S3DCA

   Summary of Contents for Frigidaire PLEW30S3DCA

  • Page 1

    INSTALLATIONAND SERVICE MUST BEPERFORMED BY A QUAUNED INSTALLER. IMPORTANT:SAVEFORLOCAL ELECTRICAL INSPECTOR'S USE. READAND SAVETHESEINSTRUCTIONS FOR FUTUREREFERENCE. FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and Hquids in the v[dnity of this or any other appliance. GENERAL iNFORMATION Tile Warmer Drawer carl be used: •...

  • Page 2

    Locate the 2 antPtip brackets supplied as shown on Important Notes to the Installer figure 1. Fix them using 2 of the 4 black head Read all the instructions contained in these installation screws (!0-16 X lY4") supplied. instructions before installing appliance, Slide the drawer into tile cutout opening until the Remove all packing material from the appliance before...

  • Page 3

    B.[nstaHation for a coutoutheightof 91/4 ( 23.5 Locate tile 2 anti-tip brackets and the 2 front supports supplied as shown on figure 3. Fix them using the 4 black head screws (10-16 X lY4") SPACER supplied Install the 4 spacers (Figure 4) supplied under drawer as shown in figure 5 using the 4 screws (I0-24 X %").

  • Page 4

    NOTES...

  • Page 5

    LA INSTALACI6N Y EL SERVIGO DEBEN SER EJECUTADOS POR UN INSTALADOR CAURCADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA EL USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS. PARA SU SEGURJDAD: No aJmacene o use gasolina u otros vapores y t_quidos...

  • Page 6

    Instalaci6n del cajon calentador Notas importantes para el instalador 1. Leatodas las instrucciones de instalaci6n antes de instalar A. tnsta[aci6n estandard: el electrodomestico, 1. Instale los 2 brackets antPvolteo como muestro la figura 1. 2. Retire todos materiales empaque Instale los usando 2 de los 4 torn illos negros (10-16 X 11/4") suministrados.

  • Page 7

    B.InstaIad6n de[caj6n calentador c onunaabertura de 9%(23.5cm) 1. Localice los2brackets antPvolteo ylos 2apoyos a nteriores APOYO suministrados como mostrado e nlafigura3.Inst_le los usando los4tornillos n egros (10-I 6 X1Y4 " )su ministrados. 2. Instalelos2 apoyos (Figura 4) suministrado conel caj6ncomomostrado en la figura 5 usandolos4 tornillos(I0_24X sA")suministrados.

  • Page 8

    NOTAS...

  • Page 9

    L'iNSTALLATiON ETL'ENTRETiEN DOIVENTF.TRE EFFECTUES PARUN iNSTALLATEUR COIVIPETENT. iMPORTANT : CONSERVEZ CESiNSTRUCTiONS P OURL'iNSPECTEUR D'ELECTRICITE LOCAL.USEZETCONSERVEZ CESiNSTRUCTiONS P OURREFERENCES ULTERiEURES. POUR VOTRE SI_CURITI_: N'entreposez et n'utiiisez pas d'essence ou autres gaz et [[quides inflammables & prox[m[t_ de cet apparel[ ou de tout autre apparel[ m_nager.

  • Page 10

    Installation d'un tiroiror_chaud Notes importantes _ Vinstallateur 1. Liseztoutes lesinstructions d'installation avant de proc6der 1. Localisez les supports anti-bascules tel qu'indique a la I'installation de cet appareil. figure 1. Fixezdes a I'aide des vis noire fournies (10-16 X 2. Retirez tout le materiel d'emballage de I'appareil avant de brancher I'alimentation dectrique.

  • Page 11

    B°installationpourunehauteurded_coupage de 91/4 (23.5 ENTRETOISE 1. Localisez les 2 supports anti-bascules et les 2 supports frontaux foumis comme indiques a la figure 3. Fixezqes I'aide des 4 visa noires fournies (10-16 X le 1X >9 2. Installez les 4 entretoises fournies (Figure 4) sous le tiroir -VlS comme indique a la figure 5 en utilisant les 4 vis (! 0-24 X 5/8").

  • Page 12

    NOTES...

Comments to this Manuals

Symbols: 0
Latest comments: