GE DNCD450GG9WC Installation Instructions Manual

,ns,o,,o,ion ! Gos yer 1@
Instructions
Questions on Installation? Call: 800.GE.CARES (US) or 800-561-3344 (Canada) I
or visit our web site at: www.GEAppliances.corn (US)
I
BEFORE YOU BEGIN
Read these instructions
completely and carefully.
• IMPORTANT- save
these instructions for local
inspector's use.
• IMPORTANT-
Observe
all governing codes and
ordinances.
• Note to Installer - Be sure to
leave these instructions with
the customer.
• Note to Customer- Keep these
instructions with your Owner's
Hanual for future reference.
• Before the old dryer is removed
from service or discarded,
remove the dryer door.
• Inspect the dryer exhaust
outlet and straighten the
outlet walls if they are bent.
• Service information and the
wiring diagram are located in
the control console.
• Do not allow children on
or in the appliance. Close
supervision of children is
necessary when the appliance
is used near children.
• Install the dryer where the
temperature is above 50°F for
satisfactory operation of the
dryer control system.
• Product failure due to
improper installation is not
covered under the Warranty.
TOOLS YOU WILL NEED
(x2)
10" ADJUSTABLE WRENCHES
SLIPJOINT PLIERS
R" PlP_ \AIP_EIF'H
FLATBLADE SCREWDRIVER
WARNING
RISK OF FIRE
• To reduce the risk of severe injury or death, follow all installation instructions.
• Clothes dryer installation must be performed by a qualified installer.
• Install the clothes dryer according to these instructions and in accordance with local
codes.
• California Safe Drinking Water and Toxic Enforcement Act
This act requires the governor of California to publish a list of substances known to the
state to cause cancer, birth defects or other reproductive harm and requires businesses
to warn customers of potential exposure to such substances. Gas appliances can
cause minor exposure to four of these substances, namely benzene, carbon monoxide,
formaldehyde and soot, caused primarily by the incomplete combustion of natural gas
or LP fuels. Properly adjusted dryers will minimize incomplete combustion. Exposure to
these substances can be minimized further by properly venting the dryer to the outdoors.
• This dryer must be exhausted to the outdoors.
• Use only rigid metal 4" diameter ductwork inside the dryer cabinet and use only UL
approved transition ducting between the dryer and the home duct.
• DO NOT install a clothes dryer with flexible plastic ducting materials. If flexible metal
(semirigid or foil-type) duct is installed, it must be UL listed and installed in accordance
with the instructions found in "Connecting The Dryer To House Vent" on page 5 of this
manual. Flexible venting materials are known to collapse, be easily crushed, and trap
lint. These conditions will obstruct dryer airflow and increase the risk of fire.
• Do not install or store this appliance in any location where it could be exposed to water
and or weather.
• Save these instructions. (Installers: Be sure to leave these instructions with the
customer).
IN THE COMMONWEALTH OF MASSACHUSETTS
• This product must be instolled bg e licensed plumber or gos fitter.
• When using bell-tgpe gos shut-off velves, theg shell be the T-hendle tgpe.
• A flexible gos connector, when used, most not exceed 3 feet.
4"DIA. M ETAL DUCT
(RECOMMENDED}
4"DIA. F LEXIBLE METAL ISEMI-RIGID}
ULLISTED TRANSITION DUCT
(LF NEEDED}
KiTWXO8X10077 (INCLUDES 2 ELBOWS}
4"DIA. F LEXIBLE METAL (FOIL T YPE}
ULLISTED TRANSiTiON DUCT
(IFNEEDED,}
MATERIALS YOU WILL NEED
%
4"DIA. M ETAL
ELBOW
4"DUCT
EXHAUST
HOOD
PIPE
COHPOUND SOAPSOLUTION
FORLEAKDETECTION
CLAMPS (2}
OR
4"SPRING
CLAMPS (2}
DUCT T APE SAFETY
GLASSES
FLEXIBLE GASLINE CONNECTOR GLOVES
Step i
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Verify your gas installation
(see
section 2).
Prepare the area and exhaust for installation of new dryer
(see section 1).
Check and ensure the existing external exhaust is clean (see
section 1) and meets attached installation specifications (see
section 6).
Remove the foam shipping pads (see section 1).
Move the dryer to the desired location.
Level your dryer (see section 8).
Connect the gas supply (see section 3) and check for leaks
(see section 4).
Connect the external exhaust (see section 7).
Step 9 Connect the power supply (see section 5).
Step 10 Check the operation of the power supply, gas connections,
and venting.
Step 11 Place the Owner's Manual and the Installation Instructions in
a location where they will be noticed by the owner.
For alcove or closet installation, see section 9.
For bathroom or bedroom installation, see section 10.
For mobile or manufactured home, see section 11.
For garage installation (if allowed by local codes), see section 12.
For side or bottom exhaust, see section 13.
234D1582PO05 31-16675 03-12 GE