Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Glomation GESBC-3130
Summary of Contents for Glomation GESBC-3130
- Page 1 Embedded Single Board Computer GESBC-3130 User’s Manual...
-
Page 2: Table Of Contents
GESBC-3130 User’s Manual Table of Contents Chapter 1 – Introducing the GESBC-3130 Single Board Computer ..........4 GESBC-3130 Overview......................... 4 Advanced Features ......................... 4 LPC-3130 ............................5 SDRAM ............................5 FLASH ............................5 USB ..............................5 ... -
Page 3: List Of Tables
GESBC-3130 User’s Manual List of Tables Table 1 Boot Mode Configuration ..................... 8 Table 2 UART Port CON8 Connector on GESBC-3130..............10 Table 7 CON2 I2C bus, SPI bus, PWM output ................10 Table 7 CON9 A/D input ........................ 11 Table 9 CON1 GPIO ........................ -
Page 4: Chapter 1 - Introducing The Gesbc-3130 Single Board Computer
GPS devices. Advanced Features The heart of the GESBC-3130 is the LPC-3130 which is the one in a series of ARM926EJ-S-based processors. The NXP LPC3130 combines an 180 MHz ARM926EJ-S CPU core, high-speed USB 2.0 On-The-Go (OTG), up to 192 KB SRAM, NAND flash controller, flexible external bus... -
Page 5: Sdram
GESBC-3130 User’s Manual Figure 1. GESBC-3130 Single Board Computer LPC-3130 The GESBC-3130 is shipped with the NXP LPC-3130 processor. For more information regarding the LPC-3130 processor please see the LPC-3130 datasheet. SDRAM The GESBC-3130 is shipped with 32MBytes of SDRAM. -
Page 6: Chapter 2 - Getting Started
Describes how to operate the GESBC-3130 Single Board Computer Assembly and Connections In order to use the GESBC-3130 the user must first assemble and connect the peripherals to the GESBC-3130, as described in the following procedure. 1. Place the GESBC-3130 on a static free surface. - Page 7 GESBC-3130 User’s Manual Please see Version 1.0 Page 7 of 18 20-Jun-11...
-
Page 8: Configurations
Chapter 4 – Software Description for more details regarding the software functionality. Configurations The GESBC-3130 has multiple boot mode. It can boot from SD/MMC card, USB port, UART, or on-board NAND FLASH. Jumpers are used to configure the GESBC-3130 to boot in different modes. -
Page 9: Chapter 3 - Gesbc-3130 Function Blocks
GESBC-3130 User’s Manual Chapter 3 – GESBC-3130 Function Blocks LPC-3130 The GESBC-3130 Single Board Computer uses the NXP LPC-3130 as the core processor on this development board. The top-level features of LPC-3130 processor are the following: • ARM926EJ-S RISC Core Processor •... -
Page 10: Usb
The GESBC-3130 Single Board Computer is shipped with one fast RS-232 UART interface. The fast UART on the GESBC-3130 serves as a debug port by U-boot and Linux kernel. The UART connector is the DB-9 connector on GESBC-3130. The signal designation is listed in the following table. -
Page 11: Usb Port
GESBC-3130 User’s Manual USB Port The GESBC-3130 Single Board Computer is shipped with a high speed USB OTG port on a USB mini A/B USB OTG connector. A/D Converter The GESBC-3130 Single Board Computer provides 4 channel 10 bit A/D converter. A 6pin 2.54mm spacing header provides the 4 A/D input channel. -
Page 12: Jtag
GESBC-3130 User’s Manual JTAG The GESBC-3130 Single Board Computer is shipped with a 10 pin connector that provides JTAG debug signals for the CPU. The JTAG provides the user with the ability to debug system level programs. The signal designation is listed in the following table. -
Page 13: Chapter 4 - Software Description
U-boot provides a simple interface for loading operating systems and applications onto the GESBC-3130 board. U-Boot uses a serial console for its input and output. The default serial port setting is 115200,8,N,1. It also supports the built-in Ethernet port and general flash programming. -
Page 14: Loading Linux Kernel And Root File System
The loading by Ethernet network is shown here. User can consult U-boot manual for other methods of loading data. After power on the GESBC-3130 board, stop the U-boot auto-execution by press any key. The following message should be shown on the terminal console on the host PC connected to the GESBC-3130 board. - Page 15 GESBC-3130 User’s Manual The net work address and server address must be set before network transfer can take place. The following commands will set the SBC IP address and server IP address, set ipaddr xxx.xxx.xxx.xxx set serverip xxx.xxx.xxx.xxx The server IP is the IP address where a TFTP server must be run. To load Linux kernel type in the...
-
Page 16: Chapter 5 - Development Tools
JTAG interface. Linux Development Tool Chain The Linux development tool chain is available at Glomation website in the support page. A host PC running Linux operating system is required to run the development tools. This guide assumes user had basic Linux or Unix application development knowledge. - Page 17 For bash shell, a good place to put is in .bashrc in your home directory. Compile Linux Kernel The GESBC-3130 is shipped with Linux kernel version 2.6.33.14. The patch for the kernel source tree is available at Glomation website in the support page.
-
Page 18: Chapter 6 - Troubleshooting
This chapter provides Troubleshooting information. Search the entries in the Problem column in order to find the item that best describes your situation. Then perform the corrective action in the same row. If the problem persists, contact Glomation. Version 1.0...