Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IP Gear Quasar Smartcell 111L
Summary of Contents for IP Gear Quasar Smartcell 111L
- Page 1 IP Gear Quasar Smartcell 111L User’s Manual Table of Contents Next Page...
- Page 2 IP Gear Ltd. and its distributors assume no responsibility for any damage or loss resulting from the use of its prod- ucts or this user manual. IP Gear Ltd. and its distributors assume no responsibility for any loss or claims by third parties, which may arise through the use of its products.
-
Page 3: Table Of Contents
IP Gear Quasar 111L Table of Contents Calling Line Identification Restriction (CLIR) ..14 Clearing a Lock ............14 Erase SMS Inbox of the SIM card......14 Immediate Dialing ..........15 Interdigit Timeout ........... 15 INTRODUCTION ............1 Network Lock ............16 Overview................. -
Page 4: Introduction
IP Gear Quasar 111L Chapter 1 This section includes: • “Overview” on page 2 Introduction • “Product Components & ID” on page 2 • “Contents of Package” on page 3 • “Safety Precautions” on page 3 Previous Page Table of Contents... -
Page 5: Overview
IP Gear Quasar 111L. The IP Gear Quasar 111L can be used with a plain analog telephone. In this case, when the hand-set is lifted, the IP Gear Quasar 111L sends a dial tone. This configuration can replace a fixed line telephone. -
Page 6: Contents Of Package
The following items may be supplied on a separate order: • Do not connect the IP Gear Quasar 111L to any power • Data cable for Fax and SMS source other than the nominal source indicated on the •... -
Page 7: Getting Started
IP Gear Quasar 111L Chapter 2 This section includes: • “Installing the Unit” on page 5 Getting Started • “Initial Start-up and LEDs” on page 7 • “Testing the Installation” on page 8 • “Instructions for Users” on page 9... -
Page 8: Installing The Unit
To install the IP Gear Quasar 111L: • with room for the metal plate 1. Select a location for the IP Gear Quasar 111L. The • with room for the antenna to stand in an upright location must meet the following criteria: position •... - Page 9 10. Close the SIM card tray. Table 1: RJ-11 Connector Pin Layout 11. Connect the routed trunk port of the PABX (FXO) to PIN # FUNCTION the LINE port (FXS) of the IP Gear Quasar 111L. Reserved Ring Ring Reserved Warning: Do not use the reserved pins.
-
Page 10: Initial Start-Up And Leds
Calls that should indicates that the unit is initializing. Once the SIM card is not be made on the IP Gear Quasar 111L can registered and operational, the STATUS LED stops be blocked by using the Toll Restriction feature blinking. -
Page 11: Testing The Installation
Note: To verify a SIM card number: remove the SIM card from the IP Gear Quasar 111L and insert it in a cellular phone. Dial out to 3. Dial out to a known cellular telephone number. The another phone with a display or use the incoming number ring-back tone should be heard. -
Page 12: Instructions For Users
If Call Duration Limit is active, calls longer than the time limit will be cut. • The IP Gear Quasar 111L collects the dialed digits and places the call when one of the following occur: • the # key is pressed •... -
Page 13: Programming
IP Gear Quasar 111L Chapter 3 This section includes: • “How to Program” on page 11 Programming • “Programming Summary” on page 12 • “Features” on page 13 • “Factory Default Values” on page 21 Previous Page Table of Contents... -
Page 14: How To Program
• If you made a lot of changes and want to start from Note: Alternately, dial through the PABX to the IP Gear Quasar fresh, or you want to delete all the programming 111L unit. changes made to the channel - use the "Restore Factory Default"... -
Page 15: Programming Summary
IP Gear Quasar 111L Programming Summary Table 3: DTMF Programming Summary Call Duration See “Call Duration Limit” on *6133*# Table 3: DTMF Programming Summary Limit page 13. Erase SMS mail- See “Erase SMS Inbox of the SIM Code Function Remarks *6150*# card”... -
Page 16: Features
IP Gear Quasar 111L Features Table 4: Audio Gain Commands Result This section lists the various IP Gear Quasar 111L fea- Increase gain * tures, which can be programmed by the user. Section Decrease gain * 4.10, has a concise summary of the programming details. -
Page 17: Calling Line Identification Restriction (Clir)
PIN code and, consequently, This parameter determines whether or not the IP Gear clears the lock. Quasar 111L sends its SIM number to the called party. 1. Dial ** 1343**#. The unit enters the programming WARNING! SIM cards lock after 3 failed tries. -
Page 18: Immediate Dialing
The confirmation tone can be delayed up to 30 seconds, followed by the # sign. For example, if you dial 10#, depending on current inbox volume. the IP Gear Quasar 111L will place the call after 10 digits have been dialed. Note: To disable this feature, enter 0#. -
Page 19: Network Lock
To use a PIN-code protected SIM-card, activate it and 3. Dial the timeout length—up to 9 seconds—followed by insert it into the IP Gear Quasar 111L. Every time the unit the # sign. For example, if you dial 5# the timeout powers up, it delivers the stored PIN code to the SIM between dialed digits is set to 5 seconds. - Page 20 IP Gear Quasar 111L Enabling Protection When the PIN Code is Known d. Dial YYYY#. The unit emits the confirmation tone, enables the new PIN code, and stores it in place of If the SIM card’s existing PIN code is known, there are the existing PIN code.
-
Page 21: Restore Factory Default
Set Pulse Drop Signaling Method mobile phone and follow the phone’s menu.) After the inserting the SIM card into the IP Gear Qua- If the PABX trunk connected to the unit supports Pulse sar 111L, clear the lock. See “Clearing a Lock” on Drop, use this command to set the unit to Pulse Drop sig- page 14. -
Page 22: Set Pulse Drop Width
IP Gear Quasar 111L Set Pulse Drop Width Set Reverse Polarity Signaling Method If Pulse Drop signalling method is used, the width of the If the PABX trunk connected to the unit supports Reverse pulse can be controlled using this command. In general—... - Page 23 IP Gear Quasar 111L There is no way to read the prefixes stored in the table. If Other DTMF commands include: you are in doubt about a specific prefix - reenter it or Table 5: Toll Restriction Commands delete it.
-
Page 24: Factory Default Values
IP Gear Quasar 111L Factory Default Values • Toll restriction is disabled • Network lock default depends on the version • Rx gain - -8db, Tx gain - +36db • CLIR enabled • SIM PIN code request disabled. Default PIN code is 1234 •... - Page 25 IP Gear Quasar 111L Chapter 4 This section includes: • “SMS Commands Overview” on page 23 • “GET Command Table” on page 23 • “SET Command Table” on page 24 Previous Page Table of Contents Next Page...
-
Page 26: Sms Commands Overview
IP Gear Quasar 111L SMS Commands Overview GET Command Table The IP Gear Quasar 111L may be controlled remotely Table 6: GET Command Table using SMS commands. The SMS message must match Command the structure described in tables Table 6 and Table 7. -
Page 27: Set Command Table
IP Gear Quasar 111L SET Command Table Table 6: GET Command Table Command Command Feature Applicable Response Syntax TRANSMIT GAIN (+6 - -24) Table 7: SET Command Table Gets the Tx Audio gain intervals of 2 db Command Main Cell is: "Response... -
Page 28: Miscellaneous
IP Gear Quasar 111L Chapter 5 This section includes: • “Call Progress Tones” on page 26 Miscellaneous • “LED Indications” on page 26 • “Troubleshooting” on page 27 • “Specifications” on page 28 Previous Page Table of Contents Next Page... -
Page 29: Call Progress Tones
IP Gear Quasar 111L Call Progress Tones STATUS The channel is handling a call. Blinking (0.2S on, 0.2S off) - During ringing The channel is idle. Indications Type ON cadence OFF cadence Remarks Slow blinking (0.5S on, 0.5S off): Dial tone Continuous The channel is initializing following power up. -
Page 30: Troubleshooting
IP Gear Quasar 111L Troubleshooting Problem Indications Solution - Verify that you have a valid SIM The chan- card Can not nel responds - Check that the destination does connect to with an error not conflict with the toll restriction... -
Page 31: Specifications
Specifications GSM module WaveCOM Wismo 2D Optional Features Requires a data connection between the IP Gear Quasar 111L and a PC with Win- General Specifications fax version 10 and up. Mains Supply Voltage 100-240 VAC, 50-60 Hz Requires a data connection between the Current Consumption 0.5 A max...
Need help?
Do you have a question about the Quasar Smartcell 111L and is the answer not in the manual?
Questions and answers