Table of Contents Firmware Operating Voltage Unpacking the CD-1 Connectors - Mains Connector Serial Number Registration - Analog outputs - Digital outputs Introduction Cleaning and Maintenance Accessories Technical Specifi cations Remote Control - Audio - Protection Front Panel - Mains...
Operating Voltage The CD-1 is available in two versions: one for 115V mains voltage and another for 230V mains voltage. Check the label on the CD-1 rear panel and verify you have the version with the proper voltage for your area.
Introduction Lyngdorf CD-1 is an audio optimized upsampling Compact Disc Player with low jitter clock and a High Performance DAC section. Features • Audio optimized CD transport mechanism with low jitter clock. • Linear Low Noise power supply based on Holmgren Transformer technology.
Accessories You should fi nd the following accessories included: digital info analog menu TUNER channel volume ENTER random repeat Mains cord Remote control Programming cable This manual...
This button is used for controlling the A-B Repeat Mode. 15. Random Switches Random play mode On or Off. 16. Eject Opens or closes the CD loader tray. 17. Repeat Toggles the CD-1 repeat function between None, Repeat One and Repeat All.
You can select a new track with the skip buttons, the Skip-Wheel (11 & 12 see below instructions) or directly with digits during pause mode. This will cause the CD-1 to position itself at the start of the se- lected track but it remains in Pause mode until the Play/Pause button is pressed again.
Page 9
Searching (Scan) past the end of the disc or before the start of the disc will stop the disc playing, unless the CD-1 is in Repeat All mode. In this case, the disc will loop-around to the start or the end of the disc.
Using the number buttons on the remote control to select a specifi c track number, the Random Play mode will cause the CD-1 to create a new play list with the selected track as the fi rst. The CD-1 will then start playing this track.
IEC320 type connector. 10. Power mode selection switch The CD-1 has a large switch above the Mains Input (9) selected to the correct voltage for your location or Country’s power supply. This switch is selected to either 115V or 230V operation.
Main Display The Main Display on the front panel of the CD-1 is the users feedback of all functionality and current status of the CD-1. When the Player is powered up the Main display screen shows the current fi rmware...
Page 13
CD-1 is now waiting for the stop time. Playing 5 of 11 1:23 Once A/B has been pressed again and the CD-1 is playing in A-B Repeat Mode, the display will show ‘AB’ in the bottom left hand corner of the display. Playing 5 of 11 1:22 When CD-1 is playing in Repeat All mode, ’rep’...
Menu System Display The Menu system shown in the display of CD-1 is the user’s feedback of all functionality in the menu and sub menu system. When entering menu mode, the fi rst item is shown as: Main Menu CD-1 <Dig.out Samplerate>...
Analog Out On/Off Enables or disables the analog section of the CD-1 hardware. Comm Address Selects the address used for the CD-1 when communicating with PC’s or other devices via the RS-232 port. Comm Speed Selects the speed used when communicating with PC’s or other devices via the RS-232 port.
Firmware Lyngdorf Audio supplies a free PC tool for upgrading the fi rmware of the CD-1. The latest revision of the tool as well as the fi rmware can be downloaded from www.Lyngdorf.com. Connectors Mains Connector Mains voltage to the CD-1 is applied via an IEC320 type connector. The supplied cable with safety ground should be used to connect the CD-1 to a mains outlet.
Cleaning and Maintenance Always unplug the unit from the electrical outlet before cleaning. This unit does not require any regular maintenance except to keep its exterior clean. Simply wipe its exte- rior with a clean soft cloth. A small amount of non-abrasive cleaner may be used on the cloth to remove any excessive dirt or fi...
Technical Specifi cations All audio measurements, except frequency response, are measured with a 20KHz low-pass fi lter in ac- cordance with AES-17. Measured on Unbalanced outputs - RCA (phono). Audio Parameter Value Note Frequency response L/R +/- 0.02 dB 20 – 20000 Hz Signal-to-noise ratio 115 dBA (‘infi...
44.1 kHz. Technical Assistance If you have any problems with or questions regarding your Lyngdorf Audio product, please contact your nearest Lyngdorf Audio representative or: Lyngdorf Audio Denmark E-mail: info@lyngdorf.com...