Replacement Parts..11 Operation......12 Troubleshooting....13 Warranty......14 Registration Card...15 LPCUS11xxx, LPCUN11xxx LSCUS11xxx, LSCUN11xxx LPLUS11xxx, LSLUS11xxx LPWUS11xxx Pour obtenir le manuel de l’usager en Francais consultez www.hayward-pool.ca. Hayward Pool Products 620 Division Street, Elizabeth NJ 07207 www.hayward.com USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
The luminaire is firmly secured to the niche and cannot be removed without the use of a tool. The niche is properly bonded UNLESS a Hayward Universal ColorLogic Niche (LFGUY1000 or LGGUY1000) is used. The luminaire has been installed by qualified personnel in compliance with the National Electrical Code (NEC) or Canadian Electric Code (CE Code) and any applicable local codes and/or regulations.
5. Offers spectacular brilliant light with low power consumption. Uses up to 86% less energy than a typical incandescent pool light. The 12 volt Hayward Universal ColorLogic and CrystaLogic LED (light-emitting diode) underwater lighting fixtures you have purchased are UL Listed to be installed in all Hayward or any other manufacturer’s light fixture housing (niche).
Install Niche (new installations) NOTE: For installation of Hayward niches, see installation instructions provided with the unit. The light fixture must be installed in a wall or on a floor of the pool or spa with the top of the lens not less than 4 inches (10 cm) below the normal water level of the pool except when the fixture is installed in an area of the swimming pool that is not used for swimming.
Page 5
When using a wallmount low voltage transformer, a junction box should be installed to make the connection to the pool/spa light. If using more than one light, an adequate amount of single or double outlet junction boxes will be required. Alternatively, Hayward low voltage junction box transformer kits (LTBUY11H65) can be used when in-line transformers are desired.
Page 6
(Figure 2). Install the trim ring by positioning the HAYWARD logo at the 11 o’clock position onto the light fixture. Twist the trim ring clockwise until it firmly locks. The Hayward logo should now be in the 12 o’clock position (Figure 3).
Page 7
Hayward website for the very latest compatibility information. In the interest of improving our products, if you find a niche that we have not listed or if you find that our list is inaccurate, please contact Hayward and provide feedback. We will send you a small gift in exchange for your time.
Page 8
For some installations into Sta-Rite and SwimQuip niches, the bottom tab may need to be removed. ® ® For some installations into Pargon and Hydrel niches, the included “tab extender” LPXADAPT1 may be required. ® ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
Page 9
Install Wiring using a Wallmount Transformer A suitable transformer must be installed which is agency listed for low-voltage swimming pool and spa lights (Hayward LTBUY11300, Intermatic model ® PX100/PX300, or equivalent). The transformer must be rated at or above the total wattage used by all attached light fixtures. Up to four Universal Col- orLogic/CrystaLogic LED lights (three pool lights max.) can be connected to a single Hayward LTBUY11300 transformer.
Page 10
Install Wiring using a Hayward Junction Box Transformer Hayward offers pool/spa light transformers designed to fit into various manufacturer’s junction boxes. Refer to the table on this page to determine which model transformer will fit your type of junction box. These transformers are designed to power a single Hayward ColorLogic/CrystaLogic LED light.
When using network control, custom colors and custom light shows can be programmed for each or all lights. An LKBUN1000 is required for each transformer in use and is designed to install into the Hayward LTBUY11300 300 Watt and Hayward Junction Box transformers. Refer to the LKBUN1000 installation manual for mounting and wiring instructions.
Light Synchronization If your pool or spa has multiple Hayward Universal ColorLogic LED lights, they may be operated independently, or they can be easily synchronized so they will all display the same colors and shows at the same time. For light synchronization, all lights must be wired to the same switch. Once installed, all lights should be automatically synchronized, however, if they get out of sync, they can be re-synchronized easily.
Troubleshooting If you have a problem with your Hayward Universal ColorLogic/CrystaLogic light, please try the following tips before calling for service: PROBLEM: Universal ColorLogic Light will not advance to the next program when it is power-cycled (turned “off” and then back “on”).
Page 14
The express limited warranty above constitutes the entire warranty of Hayward Pool Products with respect to its’ pool products and is in lieu of all other warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose. In no event shall Hayward Pool products be responsible for any consequential, special or incidental damages of any nature.
Please include me on all e-mail communications regarding Hayward Equipment or promotions. Please include me on all e-mail communications regarding Hayward Equipment or promotions. Mail to: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept or REGISTER YOUR WARRANTY ONLINE AT WWW.HAYWARD.COM...
Need help?
Do you have a question about the LPCUS11 Series and is the answer not in the manual?
Questions and answers