INTRODUCTION Foreword We are proud to offer the Model H6246 Meat Cutting Bandsaw. This machine is part of a grow- ing Grizzly family of fine machinery. When used according to the guidelines set forth in this manu- al, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to...
3. ALWAYS USE HEARING PROTECTION WHEN OPERATING Machinery noise can cause permanent hearing damage. H6246 Meat Cutting Bandsaw 4. WEAR PROPER APPAREL. DO NOT MACHINERY. wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con- tain long hair and wear non-slip footwear.
Page 8
SERVICING 22. MANY OPERATOR. Know and avoid conditions that cause the workpiece to "kickback." 23. ALWAYS BEFORE OPERATING MACHINERY. ADJUSTING KEYS DAMAGED PARTS MACHINES WILL EJECT WORKPIECE TOWARD LOCK MOBILE BASES H6246 Meat Cutting Bandsaw...
STALLED BLADE. Turn the saw off before attempting to "free" a stalled saw blade. Like all machines there is danger associ- ated with the Model H6246. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the pos- sibility of operator injury.
Circuit Breaker ...10 Amp Plug Type The Model H6246 is supplied with a 5-15 plug, similar to Figure 2. Figure 2. A 5-15 plug and receptacle. Electrocution or fire could...
Hex Wrench 4mm ... 1 Hex Wrench 3mm ... 1 Phillips Screwdriver ... 1 Block ... 1 The Model H6246 was carefully packed when it weight). left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or for the sake of expedi- ency, replacements can be obtained at your local hardware store. H6246 Meat Cutting Bandsaw...
-12- Site Considerations Floor Load The Model H6246 weighs 154 lbs. and has a base footprint of 19" W x 16" D. Most floors are suitable for your machine. Some residential floors may require additional reinforcement to support both the machine and operator.
Place the rubber feet on the bottom of the legs. With the help of an assistant, lift the bandsaw upright. H6246 Meat Cutting Bandsaw Tensioning Blade The bandsaw blade must be adequately ten- sioned so that it will cut straight and not fall off the wheel during operation.
Tighten the tracking control lock knob and close the upper wheel cover. For the best performance from your saw, regu- larly maintain the proper tracking of the blade. NOTICE Changes in the blade tension may change the blade tracking. H6246 Meat Cutting Bandsaw...
0.16"—about the thickness of a dollar bill folded twice—between the blade and support bearing; tighten the cap screw. H6246 Meat Cutting Bandsaw The blade guide bearings provide side-to-side support to help keep the blade straight while cut- ting.
Install the table brace on the back of the table, up underneath the table lip, and secure it with the four hex bolts and flat washers (Figure 13). H6246 Meat Cutting Bandsaw...
Page 19
Figure Figure 14. Hex nut threaded halfway onto cap screw. H6246 Meat Cutting Bandsaw Insert the two cap screws into the table run- ners so the heads are facing outward, and tighten the remaining two hex nuts onto the ends, as shown in Figure 15.
Use the knob bolts to tighten both fence rails to the fence brackets. Your completed assembly should look like Figure 18. Figure 18. Completed assembly of fences and H6246 Meat Cutting Bandsaw rails.
Strange or unnatural noises should be investigated and corrected before operating the machine further. Run the Model H6246 for a short time to ensure that the moving parts are working properly with no excessive vibration. If any problems develop, correct them before any further use the machine.
-20- Key Switch One of the most useful safety features of the Model H6246 is the removable key (Figure 20). To lock-out the ON/OFF switch remove the key. If at any time during operation of the bandsaw a safety hazard presents itself, immediately turn the machine OFF.
Lock the guide post in place with the lock knob. H6246 Meat Cutting Bandsaw Changing Blades Components and Hardware Needed: New Saw Blade ... 1 Tools Needed: Hex Wrench 4mm ...
Cutting Meat Your Model H6246 Meat-Cutting Bandsaw will cut through any fresh meat and almost all frozen meat. To cut meat with your bandsaw: Use the side fence to gauge the thickness of your desired cut. The front fence should brace the meat.
Failure to follow this warning may lead to sickness or death! H6246 Meat Cutting Bandsaw Cleaning the Saw To clean your bandsaw after use: Remove the table, the blade guards, the fences, the blood tray, and the meat grinder (Figure 22).
If your raw meat comes into contact with non- porous surfaces (wood), clean as described above and soak these surfaces for two minutes in a solution of 3 tablespoons of bleach to one gallon of cool water. Rinse these items well! H6246 Meat Cutting Bandsaw...
600 lb. load capacity in one small package! Figure 25. Model G8683 Mini Shop Fox Base. H6246 Meat Cutting Bandsaw H1302—Standard Earmuffs H4979—Deluxe Twin Cup Hearing Protector H4977—Work-Tunes Radio Headset Earmuffs Protect yourself comfortably with a pair of cush- ioned earmuffs.
Occasionally lubricate the tracking and height adjustment controls with the same food grade lubricant that you use on the table. DO NOT lubricate the meat grinder. The meat processed in the grinder serves as a natural lubricant. H6246 Meat Cutting Bandsaw...
Disconnect power before performing any electrical service. Electricity presents serious shock hazards that will result in severe personal injury and even death! H6246 Meat Cutting Bandsaw 110 VOLT MOTOR WIRES BLACK BLUE WHITE WHITE GREEN(GROUND)
Motor overheats. Motor stalls (resulting in blown fuses or tripped circuit). Loud repetitious noise coming from machine. Vibration when running or cutting. H6246 Meat Cutting Bandsaw Troubleshooting Possible Cause 1. Low voltage. 2. Open circuit in motor or loose connec- tions.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 37
___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly custom- ers in your area? Note: We never use names more than three times. ___Yes Comments: ________________________________________________...
Page 38
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
Page 40
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • – Trusted, Proven and a Great Value! ® Grizzly Is The Industry Leader! ® SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...