PRESIDENT George Owner's Manual
  1. Manuals
  2. Brands
  3. PRESIDENT Manuals
  4. Radio
  5. George
  6. Owner's manual

PRESIDENT George Owner's Manual

Automatic squelch control
Hide thumbs Also See for George:

Advertisement

Table of Contents

GEOR
GEOR
GEOR GE
GEOR
GEOR
Owner's manual
GE
GE
GE
GE

Advertisement

Table of Contents
loading

Related Manuals for PRESIDENT George

Summary of Contents for PRESIDENT George

  • Page 1 GEOR GEOR GEOR GE GEOR GEOR Owner's manual...
  • Page 2 Your PRESIDENT GEORGE at a glance...

  • Page 3: Table Of Contents

    SUMMARY INSTALLATION HOW TO USE YOUR CB PROTECTION BY SECURITY CODE SYSTEM TECHNICAL CHARACTERISTICS TROUBLE SHOOTING HOW TO TRANSMIT OR RECEIVE A MESSAGE GLOSSARY FREQUENCY TABLES...
  • Page 4 WARNING ! Before using, be careful never to transmit without first having connected the antenna (connection B situated on the back panel of the equipment) or without having set the SWR (Standing Wave Ra- tio) ! Failure to do so may result in destruc- tion of the power amplifier, which is not covered by the guarantee.

  • Page 5: Installation

    CB equipment. With the use of up- to-date technology, which guarantees unprecedented quality, your PRESIDENT GEORGE is a new step in personal communications and is the surest choice for the most demanding of professional CB radio users. To ensure...
  • Page 6 3) POWER CONNECTION: a) Choosing your antenna: Your PRESIDENT GEORGE is protected against an inversion of polarities. - For CB radios, the longer the antenna, the better its results. Your dealer will However, before switching it on, you are advised to check all the connections.
  • Page 7 4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING e) Press the «METER» key, with the «push-to-talk» switch pressed down, so that the equipment is in S/RF mode. YOUR SET FOR THE FIRST TIME (without trans-mitting and without using the «push-to-talk» switch on the microphone): DISPLAY a) Connect the microphone...

  • Page 8: How To Use Your Cb

    - Connect the SWR meter between the CB radio and the antenna as close as 5) SQUELCH: possible to the CB (use a maximum of 40 cm cable, type CA 2C PRESIDENT). b) To adjust the SWR meter: Suppresses undesirable back-ground noise when there are no - Set the CB to channel 20.
  • Page 9 Is for regulating microphone sensitivity, when using a microphone other than - Longer press on «MODE»: the one supplied with your PRESIDENT GEORGE. (pre-amplified). set goes to Channel 22 FM b) Also adjusts the sound volume of Public Address mode (see point 17).
  • Page 10 VOLUME knob. 17)PA (Public Address): An external loud speaker can be connected to your PRESIDENT GEORGE by the jack plug situated on the back panel PA.SP (E). By pressing the PA key, the message transmitted into the microphone will be directed towards the...
  • Page 11 - Press «CH L» (+ 10 channels): 20)CH 19 (Channel 19 AM): Set goes to the channel 32 FM. Channel 19 AM is automatically selected when you depress this key. Configuration You are in Channel 22 FM. - Press «CH L» (+ 10 channels): Set goes to the channel 2 FM.
  • Page 12 Press «CH19» - If a signal is detected on Channel 22 your CB listens to the channel and stays Set goes directly to Channel «CH19». there until the end of the signal. 21)DW (Dual Watch): - End of signal on Channel 22 FM. This function lets you watch over Channel 19 AM and the channel you are using.
  • Page 13 By immediately pressing one of the memory keys (M1 - M4) the channel and - Depression of «M1»: the modulation mode currently in use will be stored in the memory. The stops flashing, appears, long beep sounds to indicate that Channel operation is validated with a long beep.

  • Page 14: Protection By Security Code System

    b) Direct access to one of the memories, Initial configuration Channel 3 LSB. 24)SCAN: This function allows you to “scan” all the memorised channels (16). Scanning stops when a signal is detected on one of the memorised channels. At the end of the signal, scanning continues.
  • Page 15 In these two cases, the CB is blocked and it is necessary to enter the correct access code. The access code, established by PRESIDENT in the o) Press the fourth key of the new code choosing between «M1», «M2», «M3», factory or after being returned to the After Sales Service department is: «M4», and «PROGRAM»...

  • Page 16: Technical Characteristics

    D) TECHNICAL CHARACTERISTICS: E) TROUBLE SHOOTING: 1) YOUR CB RADIO WILL NOT TRANSMIT OR YOUR 1) GENERAL: TRANSMISSION IS OF POOR QUALITY: - Channels - Modulation modes AM/FM/LSB/USB - Check that the PA function is turned off. - Frequency ranges from 26.965 MHz à...

  • Page 17: Glossary

    Press the «push-to-talk» switch and announce your message «Attention sta- Big slab Motorway tions, transmission testing» which will allow you to check the clearness and the Big 10-4 Absolutely power of your signal. Release the switch and wait for a reply. You should Bleeding Signal from an adjacent channel receive a reply like, «Strong and clear».

  • Page 18: Frequency Tables

    Channel Frequency Channel Frequency Kanal Frequenzens Kanal Frequenzens We, GROUPE PRESIDENT ELECTRONICS, Route de Sète, BP 100 26,965 MHz 27,215 MHz – 34540 Balaruc – FRANCE, 26,975 MHz 27,225 MHz 26,985 MHz 27,255 MHz Declare, on our own responsibility that the CB radio-communication...
  • Page 19 Pays dans lesquels il existe des limitations particulières (Licence / Registre / seulement du canal 4 à 12 Countries in which there are particular restrictions Länder mit besonderen Beschränkungen (Lizenz / Register / nur Kanal 4 bis 12 Licence Register AM only channels 4 to 12 BLU/SSB Pays dans lequel la réglementation nationale autorise une puissance d’émission supérieure à...
  • Page 20 SIEGE SOCIAL/HEAD OFFICE - FRANCE Route de Sète - BP 100 - 34540 BALARUC Site Internet : http://www.president-electronics.com E-mail : groupe@president-electronics.com...

Table of Contents