WaterFurnace Geothermal heating and cooling system Owner's Manual page 27

TP32W01 Thermostat - Continued
PROGRAMMED OPERATION
Planning Your Program
The heating and cooling programs are separate, and must be programmed individually.
To use the factory program, set the clock and press PROGRAM
Heat, Cool, or Auto.
Entering Your Program
To Set the Clock:
1. Press PROGRAM
RUN
2. Press SET . The display will show the hour. Use TIME
TIME
and AM/PM designation.
3. Press SET again. The display will show minutes. Use TIME
TIME
4. Press PROGRAM
RUN
To Set the Day:
5. Press SET . The display will indicate a day of the week. Use TIME
DAY
current day of the week.
6. Press PROGRAM
RUN
To Set the Program:
7. Press to select HEAT (for heating program) or COOL (for cooling program).
SYSTEM
8. Press PROGRAM
VIEW
9. If you program Monday the first time you press PROGRAM
To program the other days of the week press
11 & 12. You can also copy the program from one day to another. To copy, press
and all the other days of week will be flashing. Press
TIME or TIME
BACK
FWD
10. Press TIME or TIME
FWD
Be sure to check the AM or PM on the display.
11. Press the red or blue
during this period, press
12. Press PROGRAM
VIEW
temperature for this period.
13. Press PROGRAM
VIEW
are satisfied that your program matches your schedule, press PROGRAM
mode and your program is running.
14. To program the other mode, repeat the procedure from step 6.
Temporary Program Override
Any time your program is running and you would like to override it for a specific amount of time, press
temperature you want is displayed. The display will indicate HOLD, and the number of hours remaining in the hold period is
indicated with the word HRS. To adjust the length of time for the override, press TIME
displayed as well as the HOLD period expiration time. Press TIME
would like it to resume the program. The TIME
programmed hold time has a 19 hour maximum and 15-minute minimum. Beyond 19 hours you may wish to use the vacation
hold feature. If you need to, you can adjust the temperature up or down.
Indefinite Program Hold
If you want to operate the thermostat to keep a set temperature without a program running, press PROGRAM
temperature Up or Down buttons can be used to raise or lower the temperature. The thermostat will hold the set temperature
until you return to the program by pressing PROGRAM
Pushbutton Backlight
The large numbers and letters on your LCD screen make it easy to see. In low light conditions, press the button on top of the
thermostat and the display will light up for three seconds. For ten minutes after pressing the light button, pressing any other
button will light the display for ten seconds.
For more information on thermostat operation, refer to the instruction manual shipped with your thermostat.
.
.
.
one time. The display will show MOR, the settings for time and temperature and MON.
/DAY to until you reach the day you wish to change and follow Steps 10,
ADV.
until you reach the day you want to copy to and press
to set the time on the display as selected in your HEATING or COOLING SCHEDULE.
BACK
key to adjust the temperature to match your schedule. If you want the fan ON continuously
.
FAN
one time. MOR on the display will change to DAY. Repeat steps 10 and 11 to enter time and
to continue through the entire schedule, entering time and temperature for each period. When you
or TIME
FWD
with the thermostat SYSTEM set to
RUN
or TIME to set to the current hour
FWD BACK
or TIME
FWD BACK
or TIME
FWD
it will be copied to the rest of the week.
VIEW
HOLD
/COPY again to copy the day in to the rest of the week or press
HOLD
. Programming is now complete for this
RUN
or TIME
FWD BACK
buttons adjust the time in 15 minute increments. This
BACK
.
RUN
THERMOSTAT OPERATION
to set to the current minutes.
to set to the
BACK
/COPY. The display will show COPY,
/COPY.
HOLD
or
or TIME . HOLD TILL will be
FWD BACK
buttons until you reach the time you
BACK
until the
. The
25