Installation Installationshinweise Achten Sie bei der Installation darauf, dass keine serienmäßig im Kfz vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgurte, Tank oder ähnliche Teile beschädigt bzw. entfernt werden. Vergewissern Sie sich, dass der Verstärker an dem Montageort genügend Kühlung erhält. Montieren Sie das Gerät nicht in zu kleine, abgeschlossene Gehäuse ohne Luftzirkulation, in die Nähe von wärmeabstrahlende Teilen oder elektronische Steuerungen des Fahrzeuges.
Funktionen & Bedienelemente TXi 3000 HIGH-/LOW PASS - Regler HIGH PASS (Hochpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach unten. Die Trennfrequenz ist stufenlos von 10Hz bis 1200Hz (1.2kHz) regelbar. LOW PASS (Tiefpass) - regelt die Begrenzung des Frequenzgangs der Lautsprecher nach oben.
Lautsprecher- & Cinchanschlüsse TXi 3000 2-Kanal-Modus Stereo Front- oder Hecksystem Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die Front- oder Hecklautsprecher mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + 1CH - und + 2CH -).
Lautsprecher- & Cinchanschlüsse TXi 3000 1-Kanal-Modus Mono Subwoofer gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie den Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + BRIDGED -).
Funktionen & Bedienelemente TXi 3400 LOW PASS - REGLER CH 3/4 (Tiefpass) - HIGH PASS - REGLER CH1/2 & CH3/4 (Hochpass) - regelt die Begrenzung des Frequenzgangs der regelt die Begrenzung des Frequenzgangs der Lautsprecher nach oben. Die Trennfrequenz ist Lautsprecher nach unten.
Lautsprecher- & Cinchanschlüsse TXi 3400 4-Kanal-Modus Stereo Front- und Hecksystem Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die Front- und Hecklautsprecher mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + 1CH - und + 2CH - und + 3CH - und + 4CH -).
Lautsprecher- & Cinchanschlüsse TXi 3400 2-Kanal-Modus Mono 2 Subwoofer gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die beiden Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / CH1/2 + BRIDGED - und CH3/4 + BRIDGED -).
Lautsprecher- & Cinchanschlüsse TXi 3400 3-Kanal-Modus Stereo Front- oder Hecksystem & Mono Subwoofer gebrückt Kabelanschlüsse • Verbinden Sie die Ausgänge des Steuergerätes (Radio) mit den Cincheingängen (LINE INPUT) des Verstärkers mittels einer geeigneten hochwertigen Cinchleitung. • Verbinden Sie die Lautsprecher und den Subwoofer mittels geeignetem Kabel mit den Lautsprecher-Ausgängen des Verstärkers (SPEAKER OUTPUT / + CH 1 - und + CH 2 - und den Subwoofer mit CH3/4 + BRIDGED -).
Fehlerbehebung Fehler: keine Funktion Ursache: 1. Die Verbindungskabel sind nicht korrekt angeschlossen. 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. 3. Sicherungen defekt. Im Falle des Austauschs achten Sie bitte auf den korrekten Wert der Sicherungen. Fehler: kein Ton aus Lautsprecher Ursache: 1.
Technische Daten TXi 3000 TXi 3400 Kanäle 2 x 100/200 4 x 55/110 Watt RMS/MAX. an 4 Ohm 2 x 175/350 4 x 85/170 Watt RMS/MAX. an 2 Ohm Watt RMS/MAX. an 4 Ohm mono gebrückt 1 x 350/700 2 x 170/340 >...
Installation Installation Notes The amplifier is generally mounted in the rear trunk area but can be mounted in any convenient area such as beneath a seat. Please be sure to locate this unit where you have reasonable air circulation and protection from moisture. When considering the mounting location you should minimize the length of the power and speaker leads.
Functions & Controls TXi 3000 HIGH-/LOW PASS High Pass This controller adjust the frequency of the loudspeakers onward (X-OVER switch position HP). The cut-off frequency is continuously adjustable from 10Hz to 1200Hz. This controller adjust also the Subsonic-Frequency in the LOW PASS-Mode (X-OVER switch position HP).
Speaker & RCA Connections TXi 3000 2-Channel-Mode Stereo Front- or Rearsystem RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1 + and - CH2 +) of the amplifier.
Speaker & RCA Connections TXi 3000 1-Channel-Mode Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - BRIDGED +) of the amplifier.
Functions & Controls TXi 3400 Low Pass CH 3/4 High Pass CH1/2 & CH3/4 This controller adjust the frequency of the This controller adjust the frequency of the loudspeakers upward (X-OVER switch position LP). loudspeakers onward (X-OVER switch position HP). The cut-off frequency is continuously adjustable from The cut-off frequency is continuously adjustable 30Hz to 150Hz.
Speaker & RCA Connections TXi 3400 4-Channel-Mode Stereo Front- and Rearsystem RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1 + and - CH2 + and - CH3 and - CH4 +) of the amplifier.
Speaker & RCA Connections TXi 3400 3-Channel-Mode 2 Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers/subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1/2 - BRIDGED + and the subwoofer with CH3/4 - BRIDGED +) of the amplifier.
Speaker & RCA Connections TXi 3400 3-Channel-Mode Stereo Front- or Rearsystem & Mono Subwoofer bridged RCA & Speaker wiring: • Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables. • Connect the speakers/subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1 + and - CH2 + and the subwoofer with CH3/4 - BRIDGED +) of the amplifier.
Troubleshooting System does not turn on 1. Check all fuses. 2. Check all connections. 3. Measure the +12 volt and remote turn on voltages at the amplifier terminals. If these are non existent or low, take voltage measurements at fuse holders, distribution blocks, the head unit’s +12 volt and remote leads to localize the problem. Noise problems 1.Check the speaker wiring 2.Speakers are damaged...
Specifications TXi 3000 TXi 3400 Channels 2 x 100/200 4 x 55/110 Watts RMS/MAX. into 4 Ohm 2 x 175/350 4 x 85/170 Watts RMS/MAX. into 2 Ohm Watta RMS/MAX. into 4 Ohm mono bridged 1 x 350/700 2 x 170/340 >...