Related Manuals for Pan Dacom SPEED-DSL 4.6
Summary of Contents for Pan Dacom SPEED-DSL 4.6
- Page 1 Pan Dacom Nets work together. SPEED-DSL 4.6 Ethernet connection over 4-wires Up to 4.6 Mbit/s (9900-005-001-A, 9900-006-001-A) Manual Version 1.1 SPEED-DSL 4.6 page 1 of 14 (9900-005-001-A, 9900-006-001-A)
- Page 2 Pan Dacom. This manual may not be copied, in whole or in part, or translated into other languages, without the written consent by Pan Dacom. by Pan Dacom Networking AG Version 1.1 SPEED-DSL 4.6 page 2 of 14 (9900-005-001-A, 9900-006-001-A)
- Page 3 1 power supply 1.2. Power Up the SPEED-DSL 4.6 Plug the power supply into the back of the SPEED-DSL 4.6 and connect it to the power source. Verify that the Power LED on the front of the SPEED-DSL 4.6 is illuminated.
- Page 4 Pan Dacom Nets work together. 5V DC Ethernet Connection SDSL 1 Version 1.1 SPEED-DSL 4.6 page 4 of 14 (9900-005-001-A, 9900-006-001-A)
- Page 5 Connections made with cable of a lesser gauge (e.g., 24 AWG) will link up at greater distances. Your SPEED-DSL 4.6 may not link up if the cable is in poor condition or if the cable distance is greater than a particular bandwidth will support;...
-
Page 6: Table Of Contents
4.6; either port (SDSL 1 or SDSL 2) may be used. Verify the connection: the SDSL LED on the front of the SPEED-DSL 4.6 (SDSL 1 or SDSL 2 depending upon which port was connected) will pulse green to indicate the connection is established and operational. -
Page 7: Sdsl 2
DSL 4.6. Verify the connection: solid illumination of the Ethernet Connection Lnk LED on the front of the SPEED-DSL 4.6 indicates a link has been established, IF an SDSL connection has already been made. If an SDSL connection has NOT yet been made, the Ethernet link will remain disabled (as indicated by solid illumination of the Ethernet Rx, Tx and Lnk LEDs) until at least one of the two SDSL links has been established. - Page 8 Pan Dacom Nets work together. Version 1.1 SPEED-DSL 4.6 page 8 of 14 (9900-005-001-A, 9900-006-001-A)
-
Page 9: Sdsl
There is a potential traffic problem over the Ethernet segment. Note: A SPEED-DSL 4.6 in Full Duplex mode does not have collisions; the Ethernet Collision LED is only applicable in Half Duplex mode. Version 1.1 SPEED-DSL 4.6... -
Page 10: Speed-Dsl 4.6
Pan Dacom Nets work together. Ethernet flashing amber Ethernet The SPEED-DSL 4.6 is receiving data from the activity Ethernet network. solid amber heavy Rx The SPEED-DSL 4.6 is receiving large amounts of traffic data from across the Ethernet network. A solid amber Ethernet Rx LED can also signify a lost... -
Page 11: Lnk
(as indicated by solid illumination of the Ethernet Rx, Tx and Lnk LEDs). Upon reestablishment of at least one of the SDSL links, the Ethernet connection will be reinstated and the Ethernet LEDs will reflect current Ethernet status. Version 1.1 SPEED-DSL 4.6 page 11 of 14 (9900-005-001-A, 9900-006-001-A) - Page 12 Industry Canada Regulatory Compliance Information for Class B Equipment This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. Version 1.1 SPEED-DSL 4.6 page 12 of 14 (9900-005-001-A, 9900-006-001-A)
- Page 13 GS Südwest GS Süd Kurze Straße 40 Inselkammerstraße 70794 Filderstadt Tel.: 0711-7705506- 82008 Unterhaching Tel : 089 614478 0 Technical Hotline 06103 – 932 100 Fax: 06103 - 932 413 dispatch@ffm.pandacom.de Version 1.1 SPEED-DSL 4.6 page 13 of 14 (9900-005-001-A, 9900-006-001-A)
- Page 14 Pan Dacom Nets work together. Version 1.1 SPEED-DSL 4.6 page 14 of 14 (9900-005-001-A, 9900-006-001-A)